Panasonic WJHD500A WJHD500A User Guide - Page 12

Installation, Installling The Optional Hard Disk

Get Panasonic WJHD500A - Digital Disk Recorder PDF manuals and user guides View all Panasonic WJHD500A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

INSTALLATION The installations described below should be made by qualified service personnel or system installers. s Installing the Optional Hard Disk At the time of shipment from the factory, the WJ-HD500A Disk Recorder is equipped with one hard disk drive; an optional drive can be installed to increase the hard disk storage capacity. To install the optional hard disk, follow the procedures below. 1. Unplug the power cord from the WJ-HD500A Disk Recorder, or disconnect the plug from the AC outlet. 2. Remove one screw on the control panel shown in the figure, then remove the panel by sliding it to the left and turned over. 4. Insert the absorbers on to the chassis as shown in the figure. 5. Place the hard disk on the chassis, then fix it with the four screws and sleeves with the earth lug as shown in the figure. earth lug absorber FS 16 3. Remove two screws on the tray chassis in the figure, then slide out the chassis from the Disk Recorder. FS 16 sleeve 6. Set the unit address with the jumper connector on the hard disk drive, as shown in the figure, for example. 7. Install the hard disk with the chassis into the Disk Recorder by sliding it from the front. 8. Plug in the power cable and interface flat cable prepared in the power inlet and interface connector of the hard disk as shown in the figure. 9. After installing the hard disk, secure the tray chassis and control panel by tightening the screws. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
4. Insert the absorbers on to the chassis as shown in the
figure.
5. Place the hard disk on the chassis, then fix it with the
four screws and sleeves with the earth lug as shown in
the figure.
6. Set the unit address with the jumper connector on the
hard disk drive, as shown in the figure, for example.
7. Install the hard disk with the chassis into the Disk
Recorder by sliding it from the front.
8. Plug in the power cable and interface flat cable pre-
pared in the power inlet and interface connector of the
hard disk as shown in the figure.
9. After installing the hard disk, secure the tray chassis
and control panel by tightening the screws.
12
INSTALLATION
The installations described below should be made by
qualified service personnel or system installers.
■
Installing the Optional Hard Disk
At the time of shipment from the factory, the WJ-HD500A
Disk Recorder is equipped with one hard disk drive; an
optional drive can be installed to increase the hard disk
storage capacity.
To install the optional hard disk, follow the procedures
below.
1. Unplug the power cord from the WJ-HD500A Disk
Recorder, or disconnect the plug from the AC outlet.
2. Remove one screw on the control panel shown in the
figure, then remove the panel by sliding it to the left and
turned over.
3. Remove two screws on the tray chassis in the figure,
then slide out the chassis from the Disk Recorder.
FS
16
FS
16
absorber
sleeve
earth lug