Sharp AJ-6010 AJ6010 Operation Manual - Page 82

Failed to Install the AJ-6000 Series Driver USB Interface

Get Sharp AJ-6010 PDF manuals and user guides View all Sharp AJ-6010 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Failed to Install the AJ-6000 Series Driver (USB Interface) Troubleshooting If the unit is connected to your computer by USB cable, you must install the USB driver. If you failed to install the AJ-6000 series driver onto your computer connected to the unit by USB interface, make sure to enable the USB port referring to the steps shown below. 1 Click the "Start" button, select "Settings", and then click "Control Panel". 3 Click the ( ) icon beside the "Universal serial bus controller". 2 Double-click the "System" icon and click the "Device Manager" tab. The last item listed in the Device Manager should be "Universal serial bus controller". Two items will display, your Controller chipset type and Root Hub. If these items appear, you can use USB port. If the "Universal serial bus controller" shows a yellow exclamation point or does not appear, you must check your computer manual for USB troubleshooting or contact your computer manufacturer. 4 When you make sure that the USB port is enabled, install the AJ-6000 series driver including the USB port driver, referring "INSTALLING THE SOFTWARE" in the Setup Guide and Operation Manual. 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
Troubleshooting
80
Failed to Install the AJ-6000 Series Driver (USB Interface)
If the unit is connected to your computer by USB cable, you must install the USB driver.
If you failed to install the AJ-6000 series driver onto your computer connected to the unit by USB interface, make
sure to enable the USB port referring to the steps shown below.
1
Click the "Start" button, select "Settings", and then
click "Control Panel".
2
Double-click the "System" icon and click the
"Device Manager" tab.
The last item listed in the Device Manager should be
"Universal serial bus controller".
3
Click the (
) icon beside the "Universal serial bus
controller".
Two items will display, your Controller chipset type and
Root Hub. If these items appear, you can use USB port. If the
"Universal serial bus controller" shows a yellow
exclamation point or does not appear, you must check your
computer manual for USB troubleshooting or contact your
computer manufacturer.
4
When you make sure that the USB port is enabled,
install the AJ-6000 series driver including the USB
port driver, referring "INSTALLING THE
SOFTWARE" in the Setup Guide and Operation
Manual.