Dell PowerEdge T410 Hardware Owner's Manual - Page 100

Installing a Cabled Hard Drive, Turn off the system and attached peripherals

Get Dell PowerEdge T410 PDF manuals and user guides View all Dell PowerEdge T410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

Figure 3-10. Removing a Hard Drive From a Hard Drive Bracket 1 2 1 hard drive 2 hard drive bracket NOTE: If you are not replacing the hard drive, remove the drive from the drive bracket (see Figure 3-10) and insert the empty bracket back into the drive bay. 7 Close the system. See "Closing the System" on page 91. 8 Place the system upright and on its feet on a flat, stable surface. 9 Rotate the system feet outward. 10 Reattach any peripherals and connect the system to an electrical outlet. 11 Turn on the system and attached peripherals Installing a Cabled Hard Drive WARNING: Only trained service technicians are authorized to remove the system cover and access any components inside the system. Before you begin this procedure, review the safety instructions that came with the system. 1 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet and from the peripherals. 2 Rotate the system feet inward and lay the system on a flat surface. 100 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
100
Installing System Components
Figure 3-10.
Removing a Hard Drive From a Hard Drive Bracket
NOTE:
If you are not replacing the hard drive, remove the drive from the drive
bracket (see Figure 3-10) and insert the empty bracket back into the drive bay.
7
Close the system. See "Closing the System" on page 91.
8
Place the system upright and on its feet on a flat, stable surface.
9
Rotate the system feet outward.
10
Reattach any peripherals and connect the system to an electrical outlet.
11
Turn on the system and attached peripherals
Installing a Cabled Hard Drive
WARNING:
Only trained service technicians are authorized to remove the system
cover and access any components inside the system. Before you begin this
procedure, review the safety instructions that came with the system.
1
Turn off the system and attached peripherals, and disconnect the system
from the electrical outlet and from the peripherals.
2
Rotate the system feet inward and lay the system on a flat surface.
1
hard drive
2
hard drive bracket
1
2