Dell PowerEdge T410 Hardware Owner's Manual - Page 55

Unsupported CPU - system interrupt controller

Get Dell PowerEdge T410 PDF manuals and user guides View all Dell PowerEdge T410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Table 1-3. System Messages (continued) Message Causes Corrective Actions Unable to launch System Services image. System halted! System halted after F10 Restart the system and keystroke because System update the Unified Server Services image is either Configurator repository to corrupted in the system the latest software to restore firmware or has been lost due full functionality. See the to system board replacement. Unified Server The iDRAC6 Enterprise card Configuration user flash memory may be documentation for more corrupted. information. Restore the flash memory using the latest version on support.dell.com. See the iDRAC6 user's guide for instructions on performing a field replacement of the flash memory. Unexpected interrupt in protected mode Improperly seated memory modules or faulty keyboard/mouse controller chip. Reseat the memory modules. See "Troubleshooting System Memory" on page 162. If the problem persists, see "Getting Help" on page 185. Unsupported CPU combination Unsupported CPU stepping detected Processor(s) is not supported Install a supported processor by the system. or processor combination. See "Processors" on page 135. Unsupported DIMM detected. The following DIMM has been disabled: x Invalid memory configuration. The system will run but with the specified memory module disabled. Ensure that the memory modules are installed in a valid configuration. See "General Memory Module Installation Guidelines" on page 106. About Your System 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
About Your System
55
Unable to launch
System Services
image. System
halted!
System halted after F10
keystroke because System
Services image is either
corrupted in the system
firmware or has been lost due
to system board replacement.
The iDRAC6 Enterprise card
flash memory may be
corrupted.
Restart the system and
update the Unified Server
Configurator repository to
the latest software to restore
full functionality. See the
Unified Server
Configuration user
documentation for more
information.
Restore the flash memory
using the latest version on
support.dell.com. See the
iDRAC6 user's guide for
instructions on performing a
field replacement of the
flash memory.
Unexpected
interrupt in
protected mode
Improperly seated memory
modules or faulty
keyboard/mouse controller
chip.
Reseat the memory modules.
See "Troubleshooting
System Memory" on
page 162. If the problem
persists, see "Getting Help"
on page 185.
Unsupported CPU
combination
Unsupported CPU
stepping
detected
Processor(s) is not supported
by the system.
Install a supported processor
or processor combination.
See "Processors" on
page 135.
Unsupported DIMM
detected. The
following DIMM
has been
disabled:
x
Invalid memory
configuration. The system
will run but with the
specified memory module
disabled.
Ensure that the memory
modules are installed in a
valid configuration. See
"General Memory Module
Installation Guidelines" on
page 106.
Table 1-3.
System Messages
(continued)
Message
Causes
Corrective Actions