Dell PowerEdge T430 Dell PowerEdge T430 Owners Manual - Page 170

System board jumper settings, Disabling a forgotten password, Password

Get Dell PowerEdge T430 PDF manuals and user guides View all Dell PowerEdge T430 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 170 highlights

Ite Connector m 33 BP_SIG 34 ODD_PWR Description Backplane signal connector Optical drive power connector System board jumper settings For information on resetting the password jumper to disable a password, see Disabling a Forgotten Password. Table 5. System board jumper settings Jumper Setting Description PWRD_EN The password reset feature is enabled (pins 2-4). NVRAM_CLR The password reset feature is disabled (pins 4-6). The iDRAC local access is unlocked at the next AC power cycle. The configuration settings are retained at the next system boot (pins 3-5). The configuration settings are cleared at system boot (pins 1-3). Disabling a forgotten password The system's software security features include a system password and a setup password. The password jumper enables these password features or disables them and clears any password(s) currently in use. Prerequisites CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. Steps 1. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 2. Open the system. 3. Move the jumper on the system-board jumper from pins 4 and 6 to pins 2 and 4. 4. Close the system. The existing passwords are not disabled (erased) until the system boots with the jumper on pins 2 and 4. However, before you assign a new system and/or setup password, you must move the jumper back to pins 4 and 6. NOTE: If you assign a new system and/or setup password with the jumper on pins 2 and 4, the system disables the new password(s) the next time it boots. 5. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. 170

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
Ite
m
Connector
Description
33
BP_SIG
Backplane signal connector
34
ODD_PWR
Optical drive power connector
System board jumper settings
For information on resetting the password jumper to disable a password, see
Disabling a Forgotten
Password
.
Table 5. System board jumper settings
Jumper
Setting
Description
PWRD_EN
The password reset feature is enabled (pins 2–4).
The password reset feature is disabled (pins 4–6).
The iDRAC local access is unlocked at the next AC
power cycle.
NVRAM_CLR
The configuration settings are retained at the next
system boot (pins 3–5).
The configuration settings are cleared at system
boot (pins 1–3).
Disabling a forgotten password
The system's software security features include a system password and a setup password. The password
jumper enables these password features or disables them and clears any password(s) currently in use.
Prerequisites
CAUTION: Many repairs may only be done by a certified service technician. You should only
perform troubleshooting and simple repairs as authorized in your product documentation, or as
directed by the online or telephone service and support team. Damage due to servicing that is
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
Steps
1.
Turn off the system, including any attached peripherals, and disconnect the system from the
electrical outlet.
2.
Open the system.
3.
Move the jumper on the system-board jumper from pins 4 and 6 to pins 2 and 4.
4.
Close the system.
The existing passwords are not disabled (erased) until the system boots with the jumper on pins 2
and 4. However, before you assign a new system and/or setup password, you must move the jumper
back to pins 4 and 6.
NOTE:
If you assign a new system and/or setup password with the jumper on pins 2 and 4, the
system disables the new password(s) the next time it boots.
5.
Reconnect the system to its electrical outlet and turn the system on, including any attached
peripherals.
170