HP 2500c Service Manual - Page 160

Installing the Service Station

Get HP 2500c - Pro Printer PDF manuals and user guides View all HP 2500c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 160 highlights

Replacement of Parts Installing the Service Station Step 1. Gently slide the new service station into the printer until the screw holes are aligned. Step 2. Reconnect the service station connector. Ensure that it is properly plugged in. Step 3. Replace the three screws at the top of the service station in order (that is, replace number one, followed by two and then three). Step 4. Put back the service station side cover. Step 5. Replace the two screws for the service station side cover. Step 6. Close the rear access door. Step 7. Place the printhead access door by fitting the left tab under the top cover. Step 8. Plug in the power cord and turn on the printer. Note To ensure that the alignment of the Service Station with the Printheads is correct, replace the Service Station screws in the correct order when installing the Service Station. 7-10 Removal and Replacement of Parts (without Calibration)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
Removal and Replacement of Parts (without Calibration)
7-10
Replacement of Parts
Installing the Service Station
Step 1.
Gently slide the new service station into the printer until the screw holes are aligned.
Step 2.
Reconnect the service station connector.
Ensure that it is properly plugged in.
Step 3.
Replace the three screws at the top of the service station in order (that is, replace number one,
followed by two and then three).
Step 4.
Put back the service station side cover.
Step 5.
Replace the two screws for the service station side cover.
Step 6.
Close the rear access door.
Step 7.
Place the printhead access door by fitting the left tab under the top cover.
Step 8.
Plug in the power cord and turn on the printer.
Note
To ensure that the alignment of the Service Station with the Printheads is correct, replace the Service
Station screws in the correct order when installing the Service Station.