HP 2500c Service Manual - Page 86

Red_dm_mlc_read_stopped_error

Get HP 2500c - Pro Printer PDF manuals and user guides View all HP 2500c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

368 RED_DM_IO_ECP_UNSUPPORTED_CHANNEL I/O problems -firmware problem => reset printer or PCA replacement Data received on unsupported channel. 369 RED_DM_IO_UNSUPPORTED_SOCKET I/O problems -firmware problem => reset printer or PCA replacement 371 RED_DM_MLC_CREDIT_GONE_BAD I/O problems -firmware problem => reset printer or PCA replacement 372 RED_DM_MLC_CREDIT_GONE_BAD2 I/O problems -firmware problem => reset printer or PCA replacement I/O problems -firmware problem => reset printer or PCA 373 RED_DM_MLC_INSUFFICIENT_MEM replacement I/O problems -firmware problem => reset printer or PCA replacement 374 RED_DM_MLC_COULDNT_ALLOC_OUTPUT I/O problems -firmware problem => reset printer or PCA replacement 375 RED_DM_MLC_UNKNOWN_DATA_CONTROL I/O problems -firmware problem => reset printer or PCA replacement 376 RED_DM_MLC_GET_INPUT_FAILED I/O problems -firmware problem => reset printer or PCA replacement 377 RED_DM_MLC_DEFAULT_CONFIG_FAIL I/O problems -firmware problem => reset printer or PCA replacement 378 RED_DM_MLC_MIDPACKET_CHANNEL I/O problems -firmware problem => reset printer or PCA replacement 379 RED_DM_MLC_READ_STOPPED_ERROR I/O problems -firmware problem => reset printer or PCA replacement 381 RED_DM_SOCKET_MULTIPLE_READS I/O problems -firmware problem => reset printer or PCA replacement 382 RED_DM_SOCKET_ILLEGAL_TAG I/O problems -firmware problem => reset printer or PCA replacement 397 RED_DM_SYS_PARAMETER_ERR Not used 398 RED_DM_INVALID_PEN Not used 399 RED_DM_NONSPEC_ERROR Not used Generic error trap (no additional information). Mechanism Code Errors 411 MECH_BAD_MECHWARE 412 MECH_BAD_RESOLUTION 413 MECH_BAD_INIT 414 MECH_THERMAL_SHORT 415 MECH_CARRIAGE_JAM 416 MECH_NO_MEMORY 417 MECH_FAIL_ADC_CAL 418 MECH_ADC_RAIL 419 MECH_VREF_PROB Not supported Mechware command Print resolution not supported Firmware code error - subsystem failed Not used Carriage blocked - Encoder strip/ carriage motor/ carriage PCA/ Harness/ Logic PCA error Firmware error or not enough memory - reset printer Not used Not used Not used Someone asked for an unsupported resolution. TaskSpawn. Pen temperature went over 95 degrees. Carriage servo failure detected. Failed the internal ADC CAL. The ADC was at the rails (was 423). The ADC was probably overdriven. 2-28 Operating Overview

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
Operating Overview
2-28
368
RED_DM_IO_ECP_UNSUPPORTED_CHANNEL
I/O problems –firmware problem => reset printer or PCA
replacement
Data received on unsupported channel.
369
RED_DM_IO_UNSUPPORTED_SOCKET
I/O problems –firmware problem => reset printer or PCA
replacement
371
RED_DM_MLC_CREDIT_GONE_BAD
I/O problems –firmware problem => reset printer or PCA
replacement
372
RED_DM_MLC_CREDIT_GONE_BAD2
I/O problems –firmware problem => reset printer or PCA
replacement
373
RED_DM_MLC_INSUFFICIENT_MEM
I/O problems –firmware problem => reset printer or PCA
replacement I/O problems –firmware problem => reset printer or
PCA replacement
374
RED_DM_MLC_COULDNT_ALLOC_OUTPUT
I/O problems –firmware problem => reset printer or PCA
replacement
375
RED_DM_MLC_UNKNOWN_DATA_CONTROL
I/O problems –firmware problem => reset printer or PCA
replacement
376
RED_DM_MLC_GET_INPUT_FAILED
I/O problems –firmware problem => reset printer or PCA
replacement
377
RED_DM_MLC_DEFAULT_CONFIG_FAIL
I/O problems –firmware problem => reset printer or PCA
replacement
378
RED_DM_MLC_MIDPACKET_CHANNEL
I/O problems –firmware problem => reset printer or PCA
replacement
379
RED_DM_MLC_READ_STOPPED_ERROR
I/O problems –firmware problem => reset printer or PCA
replacement
381
RED_DM_SOCKET_MULTIPLE_READS
I/O problems –firmware problem => reset printer or PCA
replacement
382
RED_DM_SOCKET_ILLEGAL_TAG
I/O problems –firmware problem => reset printer or PCA
replacement
397
RED_DM_SYS_PARAMETER_ERR
Not used
398
RED_DM_INVALID_PEN
Not used
399
RED_DM_NONSPEC_ERROR
Not used
Generic error trap (no additional information).
Mechanism Code Errors
411
MECH_BAD_MECHWARE
Not supported Mechware command
412
MECH_BAD_RESOLUTION
Print resolution not supported
Someone asked for an unsupported resolution.
413
MECH_BAD_INIT
Firmware code error – subsystem failed
TaskSpawn.
414
MECH_THERMAL_SHORT
Not used
Pen temperature went over 95 degrees.
415
MECH_CARRIAGE_JAM
Carriage blocked – Encoder strip/ carriage motor/ carriage PCA/
Harness/ Logic PCA error
Carriage servo failure detected.
416
MECH_NO_MEMORY
Firmware error or not enough memory – reset printer
417
MECH_FAIL_ADC_CAL
Not used
Failed the internal ADC CAL.
418
MECH_ADC_RAIL
Not used
The ADC was at the rails (was 423).
419
MECH_VREF_PROB
Not used
The ADC was probably overdriven.