HP 2500c Service Manual - Page 83

139 DEFERRED_ERROR_TRAP 141 NVM_ERR_NOT_INIT 142 NVM_ERR_GENERIC 143 NVM_ERR_DEVICE_ABSENT 144 NVM_ERR_WRITE 145 NVM_ERR_READ 146 NVM_ERR_READBACK 147 NVM_ERR_DATA_NOT_VALID 148 NVM_ERR_UNKNOWN_TAG 149 NVM_ERR_UNKNOWN_FORMAT 151 NVM_ERR_BAD_CHIP_TAG 152 NVM_ERR_BAD_FAMILY 153 NVM_ERR_BAD_COLOR 154 NVM_ERR_TSR_VALUE 155 NVM_ERR_DROP_VALUE 156 NVM_ERR_BAD_TOKEN 157 NVM_ERR_BAD_WRITE_PROT 158 NVM_ERR_BAD_MODEL_NUM 159 NVM_ERR_INCOMPAT_INK 161 NVM_ERR_BAD_MFG_WEEK 162 NVM_ERR_SPARE 163 NVM_ERR_POOL_ALLOC_FAIL 164 NVM_ERR_ACU_BAD_SIZE 165 NVM_ERR_DUPLICATE_TAG 166 NVM_ERR_TOKEN_MISLOC 167 NVM_ERR_I2C_CONF_FAIL Memory Manager 171 MM_PROC_WAITING 172 MM_SIGNAL_ERR 173 MM_MAX_WAIT_ERR Error happened during power up but printer recovered Not used Not used NVM errors Reset printer =>Replace logic PCA NVM errors Reset printer =>Replace logic PCA NVM errors Reset printer =>Replace logic PCA NVM errors Reset printer =>Replace logic PCA NVM errors Reset printer =>Replace logic PCA NVM errors Reset printer =>Replace logic PCA NVM errors Reset printer =>Replace logic PCA Penhead and cartridge errors -Not used Penhead and cartridge errors -Not used Penhead and cartridge errors -Not used Penhead and cartridge errors -Not used Penhead and cartridge errors -Not used Penhead and cartridge errors -Not used Penhead and cartridge errors -Not used Penhead and cartridge errors -Not used Penhead and cartridge errors -Not used Penhead and cartridge errors -Not used Penhead and cartridge errors -Not used System recources - Reset printer Penhead and cartridge errors -Not used Penhead and cartridge errors -Not used Penhead and cartridge errors -Not used Bus used for connecting devices on the PCA experiences error. Reset Printer => Replace PCA Printer error-trapped in a previous lifetime. Attempt to read/write before init. Non-specific NVM error. Requested memory device did not respond. Protocol error on write operation to NVM. Protocol error on read operation to NVM. Failed readback/verify after write. Device works OK. Data tag invalid. Chip functions but has invalid format. Acumen's chip tag unrecognized. Acumen's family ID unrecognized. Acumen's color code did not match device ID. Acumen TSR value = 0. Acumen drop volume = 0. Token area failed zero-write self test. Write-protect area failed self test. Acumen Model Number field out of range. Non-approved bit and "JETSERIES". Mfg week > 51. Previously was Gas Gauge Gap. No memory to allocate pool from. Token Write-protected or Scratchpad size = 0. Two identical tags were found in an Acumen chip. Status superfield not located in token area. A failure was detected on the serial bus used to access NVM devices (I2C bus). The following extended error codes apply : 001 = STUCK_LO_SDA 002 = STUCK_HI_SDA 004 = STUCK_LO_SCL 005 = STUCK_LO_SCL + STUCK_LO_SDA 006 = STUCK_LO_SCL + STUCK_HI_SDA 008 = STUCK_HI_SCL 009 = STUCK_HI_SCL + STUCK_LO_SDA 010 = STUCK_HI_SCL + STUCK_HI_SDA Not used Not used Not used Memory Manager error traps. MM debug = 0. Operating Overview 2-25