IBM 621410U Hardware Maintenance Manual - Page 27

Message, Description, Explanation, Action

Get IBM 621410U - IntelliStation E - Pro 6214 PDF manuals and user guides
UPC - 087944665854
View all IBM 621410U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Table 3. NetWare driver messages for the Ethernet controller (continued) Message Description Duplicate slot numbers detected. Explanation: An attempt has been made to bind the same slot number more than once. 'xxx' is not supported for AFT team. Action: Check the slot numbers entered during the bind. Adapter slot numbers must be valid and unique. If the problem persists, contact the network administrator. Explanation: A bind command has been issued for adapters not supported by AFT.NLM. Primary and Secondary adapters do not match. AFT group is not created. Action: Make sure that you attempt to bind only adapters supported by AFT.NLM. Explanation: A bind command was entered for an adapter team that is a combination of computer and client adapters. An AFT team must be a grouping of the same classification of adapter. Requested number of Secondary cards are not found. Action: Verify that all the adapters bound in a team are of the same classification. Explanation: The number of adapters specified in the bind command could not be located. Action: Verify the numbers and slot locations of the adapters to be bound. If the problem persists, contact the network administrator. Failed to create AFT group. Make sure that the drivers for supported adapters are loaded, primary adapter is bound to protocols, and secondary adapter is not bound to any protocols. Explanation: Binding of protocol failed. Protocol is either not bound to any adapter or is bound to more than one adapter in the group. Action: Ensure that the protocol is bound to only one adapter in an AFT team. Error identifying slot numbers for Explanation: The mapping between the board name entered and the slot the specified board names. number for an adapter could not be established. Action: Check the board name for the adapter before issuing the bind command. If the problem persists, contact the network administrator Can't unbind specified slot from AFT group. Make sure that the slot you specified is for the primary adapter in an AFT group. Explanation: The number entered in the unbind command was not the primary adapter in an AFT group. Action: Reissue the unbind command and specify the slot number for the primary adapter LAN adapter at slot nnnn (Port 0xaa) failed to reset. Check the state of the adapter. Explanation: The adapter that you specified could not be initialized. Action: 1. Load the driver for the supported adapter. 2. Check that the adapter is seated properly in the slot and try loading the AFT module again. AFT is not supported on this version of NetWare. If the problem persists, contact the network administrator. Explanation: The NetWare on your computer is not a version supported by AFT. Action: Load and bind AFT only on supported versions of NetWare (currently version 4.11 and above). Diagnostics 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
Table 3. NetWare driver messages for the Ethernet controller (continued)
Message
Description
Duplicate slot numbers detected.
Explanation:
An attempt has been made to bind the same slot number more
than once.
Action:
Check the slot numbers entered during the bind. Adapter slot numbers
must be valid and unique. If the problem persists, contact the network
administrator.
’
xxx’
is not supported for AFT
team.
Explanation:
A bind command has been issued for adapters not supported by
AFT.NLM.
Action:
Make sure that you attempt to bind only adapters supported by
AFT.NLM.
Primary and Secondary adapters
do not match. AFT group is not
created.
Explanation:
A bind command was entered for an adapter team that is a
combination of computer and client adapters. An AFT team must be a
grouping of the same classification of adapter.
Action:
Verify that all the adapters bound in a team are of the same
classification.
Requested number of Secondary
cards are not found.
Explanation:
The number of adapters specified in the bind command could not
be located.
Action:
Verify the numbers and slot locations of the adapters to be bound. If
the problem persists, contact the network administrator.
Failed to create AFT group. Make
sure that the drivers for supported
adapters are loaded, primary
adapter is bound to protocols, and
secondary adapter is not bound to
any protocols.
Explanation:
Binding of protocol failed. Protocol is either not bound to any
adapter or is bound to more than one adapter in the group.
Action:
Ensure that the protocol is bound to only one adapter in an AFT team.
Error identifying slot numbers for
the specified board names.
Explanation:
The mapping between the board name entered and the slot
number for an adapter could not be established.
Action:
Check the board name for the adapter before issuing the bind
command. If the problem persists, contact the network administrator
Can
’
t unbind specified slot from
AFT group. Make sure that the slot
you specified is for the primary
adapter in an AFT group.
Explanation:
The number entered in the unbind command was not the
primary adapter in an AFT group.
Action:
Reissue the unbind command and specify the slot number for the
primary adapter
LAN adapter at slot
nnnn
(Port
0x
aa
) failed to reset. Check the
state of the adapter.
Explanation:
The adapter that you specified could not be initialized.
Action:
1.
Load the driver for the supported adapter.
2.
Check that the adapter is seated properly in the slot and try loading the
AFT module again.
If the problem persists, contact the network administrator.
AFT is not supported on this
version of NetWare.
Explanation:
The NetWare on your computer is not a version supported by
AFT.
Action:
Load and bind AFT only on supported versions of NetWare (currently
version 4.11 and above).
Diagnostics
19