Yamaha AW2816 Owner's Manual - Page 325
Additional functions in the TR View
View all Yamaha AW2816 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 325 highlights
F I (Input monitor) This column indicates the type of signal monitored by tracks 1-16. This will indicate "q" when monitoring the track playback, and " " when monitoring the signal sent to the input of the track (input source). The type of signal being monitored will change depending on the settings of the INPUT MONITOR column (9), the state of the REC TRACK SELECT [1]-[16] keys, and the current running mode. G Track view The regions (continuous audio data recorded in a single operation) included in each track are displayed as bar graphs in this area. The vertical line in this area indicates the current location. The symbols displayed at the bottom of the frame indicate locate points or markers that have been set in those locations. The following types of symbols are displayed. • S Start point • E End point • I In point • O Out point • A A point • B B point • 1-99 Markers 1-99 • R Relative time zero location Tip! The "R" symbol that indicates the relative time zero location will be displayed only if relative time is selected as the counter display method. Relative time can be selected in the METER screen/Meter 2 page. H ALL MUTE OFF When you move the cursor to this button and press the [ENTER] key, muting will be turned off for all tracks. Tracks that have been muted due to limitations in the number of simultaneously playable tracks cannot be unmuted unless you reduce the number of recordready tracks, or mute other tracks. I INPUT MONITOR This selects the input monitor mode (the way in which input monitor will be switches for each track). This is the same function as the INPUT MONITOR area of the METER screen. For details refer to page 351. J Current position The vertical line in this box indicates the approximate current location between the start and end points of the song. The small symbols below the box indicate the approximate location of the locate points and markers. K METRO. (Metronome) This area turns the metronome on/off (the ON/OFF button) and adjusts the volume of the metronome (the knob). When you turn on the internal metronome and raise the volume, the metronome sound will be output from the MONITOR OUT/PHONES jacks during song playback or recording. Tip! • The tempo and time signature of the metronome are specified in the SONG screen Tempo Map page. • If necessary, you can select the output signal of the internal metronome (MET) as an input source for input channels 1-8. Assignments to input channels are made in the PATCH screen/Patch IN page. • If the internal metronome is selected as an input source for an input channel, the metronome output will be sent to the corresponding input channel without regard to the settings of the ON/OFF button or volume knob in the METRO. area. s Additional functions in the TR View page In the TR View page you can press the [SHIFT] key to assign the following additional functions to the [F1]- [F4] keys. • [F1] (REMAIN) key Displays the remaining available recording time (hours: minutes) in the counter located in the upper part of the screen. Hold down the [SHIFT] key and press the [F1] key once again to return to the normal counter display. Tip! The remaining recordable time will differ depending on the number of tracks that are currently in recordready mode. For example if you increase the number of tracks in record-ready mode from one track to two tracks, the remaining recordable time will be halved. • [F2] (WAVE) key Displays the audio of the desired track as a waveform. This is convenient when you want to set a locate pointer or marker while viewing the waveform. • [F3] (X-ZOOM IN) key Each time you press the [SHIFT] key + [F3] (XZOOM IN) key, the track view 7 will zoom-in horizontally (four levels). • [F4] (X-ZOOM OUT) key Each time you press the [SHIFT] key + [F4] (XZOOM OUT) key, the track view 7 will zoom-out horizontally (four levels). TRACK screen Reference section 323