Garmin GPSMAP 6012 Owner's Manual - Page 101

Radar, Radar Setup, Antenna Size, Enable No-transmit Zone, Angle 1, Adjust, Front of Boat

Get Garmin GPSMAP 6012 PDF manuals and user guides View all Garmin GPSMAP 6012 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Radar Setting the Radar Antenna Size You can indicate the size of the radar antenna in order to optimize the radar picture. Until you specify the antenna size, the "Radar needs to be configured" message appears. Note: You can set the antenna size for GMR 404, 406, 604 xHD, 606 xHD, 1204 xHD, or 1206 xHD radar only. 1. From the Home screen, select Radar > Radar Setup > Antenna Size. 2. Select 4 Foot or 6 Foot. Turning On and Configuring a Radar No-transmit Zone You can indicate an area within which the radar scanner does not transmit signals. Note: You can set a radar no-transmit zone for GMR 604 xHD, 606 xHD, 1204 xHD, or 1206 xHD radar only. 1. From the Home screen, select Radar > Radar Setup > Enable No-transmit Zone. The no-transmit zone is indicated by a shaded area on the Radar screen. 2. Select Angle 1 > Adjust > Move. 3. Select Up or Down to adjust the size of the no-transmit zone. 4. Select Angle 2 > Adjust > Move. 5. Select Up or Down to adjust the size of the no-transmit zone. Front-of-boat Offset The front-of-boat offset compensates for the physical location of the radar scanner on a boat, if the radar scanner does not align with the bow-stern axis. Measuring the Potential Front-of-boat Offset 1. Using a magnetic compass, take an optical bearing of a stationary target located within viewable range. 2. Measure the target bearing on the radar. 3. If the bearing deviation is more than +/- 1°, set the front-of-boat offset. Setting the Front-of-boat Offset Before you can set the front-of-boat offset, you must measure the front-of-boat offset (page 95). The front-of-boat offset setting configured for use in one radar mode is applied to every other radar mode and to the Radar Overlay. 1. From the Home screen, select Radar > Radar Setup > Front of Boat. 2. Select and hold Up or Down to adjust the offset. GPSMAP® 6000/7000 Series Owner's Manual 95

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
GPSMAP
®
6000/7000 Series Owner’s Manual
·µ
Radar
Setting the Radar Antenna Size
You can indicate the size of the radar antenna in order to optimize the radar picture. Until you
specify the antenna size, the “Radar needs to be configured” message appears.
NOTE
: You can set the antenna size for GMR 404, 406, 604 xHD, 606 xHD, 1204 xHD, or 1206
xHD radar only.
1. From the Home screen, select
Radar
>
Radar Setup
>
Antenna Size
.
2. Select
4 Foot
or
6 Foot
.
Turning On and Configuring a Radar No-transmit Zone
You can indicate an area within which the radar scanner does not transmit signals.
NOTE
: You can set a radar no-transmit zone for GMR 604 xHD, 606 xHD, 1204 xHD, or 1206
xHD radar only.
1. From the Home screen, select
Radar
>
Radar Setup
>
Enable No-transmit Zone
.
The no-transmit zone is indicated by a shaded area on the Radar screen.
2. Select
Angle 1
>
Adjust
>
Move
.
3. Select
Up
or
Down
to adjust the size of the no-transmit zone.
4. Select
Angle 2
>
Adjust
>
Move
.
5. Select
Up
or
Down
to adjust the size of the no-transmit zone.
Front-of-boat Offset
The front-of-boat offset compensates for the physical location of the radar scanner on a boat, if the
radar scanner does not align with the bow-stern axis.
Measuring the Potential Front-of-boat Offset
1. Using a magnetic compass, take an optical bearing of a stationary target located within viewable
range.
2. Measure the target bearing on the radar.
3. If the bearing deviation is more than +/- 1°, set the front-of-boat offset.
Setting the Front-of-boat Offset
Before you can set the front-of-boat offset, you must measure the front-of-boat offset (
page 95
).
The front-of-boat offset setting configured for use in one radar mode is applied to every other radar
mode and to the Radar Overlay.
1. From the Home screen, select
Radar
>
Radar Setup
>
Front of Boat
.
2. Select and hold
Up
or
Down
to adjust the offset.