Home » Intel Manuals » Desktops » Intel S7000FC4UR » Manual Viewer

Intel S7000FC4UR Product Guide - Page 36

Cooling Subsystem

UPC - 735858194259

Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Cooling Subsystem Caution: The chassis top cover must be installed for proper system cooling. Cooling components must be hot-swapped within two minutes. This time period applies only to the time that the cooling component is physically removed, not from the time of failure. The cooling subsystem consists of hot-swap, redundant (7+1) fans. In a redundant configuration, the system supports one fault at a time, either one fan fault or one power supply fault, and it supports hot-swapping one component at a time. If a cooling component fails, the system cooling is maintained and the system continues to operate while the component is hot-swapped. Each front fan assembly has one status LED. The LED is off when both fans are operating normally. The LED illuminate amber if one or both of the fans fails. Failed front fans can be hot-swapped from the front of the system. Each rear fan has one status LED. The LED is off when the fan is operating normally and illuminates amber if the fan fails. Failed rear fans can be replaced from the top of the system when the top cover is removed. Figure 9. Rear Fan Locations AF002242 18 Intel® Server System S7000FC4UR Product Guide

Section	Page
Safety Information	3
Important Safety Instructions	3
Wichtige Sicherheitshinweise	3
Consignes de sécurité	3
Instrucciones de seguridad importantes	3
Warnings	4
Preface	7
About this Manual	7
Manual Organization	7
Additional Information and Software	8
1 System Description	19
System Features	20
System Front	22
Front Control Panel	23
System Rear	28
Processors	30
System Memory	30
Power Subsystem	32
Power Supply Modules	32
Power Supply Consumption	34
Cooling Subsystem	36
Hot-swap PCI Slots	37
Peripherals	38
Hot-Swap Hard Drive	39
Optical Drive Bay	40
5 ¹-inch Half-height Drive Bay	40
System Board Set	40
Main Board	41
Memory Board	46
I/O Riser Board (optional)	48
SAS Riser Board (optional)	49
Front Panel Board	50
SAS Backplane Board	51
Power Distribution Board	53
Server and Platform Management	53
2 Starting Up and Shutting Down the Server	55
Powering Up the Server	55
Shutting Down the Server	55
3 Intel® Server Deployment Toolkit	57
4 Server Utilities	59
Using the BIOS Setup Utility	59
Navigating the BIOS Setup Utility	59
System Configuration Reset	61
Rolling BIOS	63
Booting from Backup Image	63
Console Redirection	64
Serial Configuration Settings	64
Keystroke Mappings	65
Limitations	66
Interface to Server Management	66
Platform Confidence Test	67
Running the Platform Confidence Test	68
Intel® Deployment Assistant	69
System Setup and Configuration Utilities	69
Save and Restore System Configuration (SYSCFG)	70
FWPIAUPD Firmware Load Utility	70
One-boot Flash Update Utility (OFU)	71
IFLASH32 BIOS Load Utility	71
FRUSDR Load Utility	71
Extensible Firmware Interface (EFI) Shell	72
5 User-Serviceable Components	75
Before You Begin	75
Tools and Supplies Needed	75
System References	75
Removing and Installing the Chassis Cover	75
Removing the Top Cover	76
Installing the Top Cover	77
Hot-swapping a Front System Fan	77
Hot-swapping a Rear System Fan	78
Hot-swapping a Hard Drive	80
Removing a Hard Drive Carrier	81
Mounting a Hard Drive in a Carrier	81
Installing a Hard Drive Carrier	83
Hot-swapping a Power Supply	84
Installing and Removing PCI Express* Add-in Cards	86
Removing a Hot-swap PCI Card, Operating System Interface	87
Removing a Hot-swap PCI Card, Hardware Interface	89
Installing a Hot-swap PCI Card	90
Removing a Non-hot-swap PCI Card	92
Installing a Non-hot-swap PCI Card	93
Installing and Removing Memory Boards	93
Removing a Memory Board	94
Installing a Memory Board	96
Installing and Removing DIMMs	97
Installing DIMMs	99
Removing DIMMs	102
6 Technician Maintenance	103
Before You Begin	103
Tools and Supplies Needed	103
System References	103
Component Locations	104
Removing and Installing the Top Cover	108
Removing the Top Cover	108
Installing the Top Cover	109
Removing and Installing the Processor Air Baffle	110
Removing the Processor Air Baffle	110
Installing the Processor Air Baffle	112
Removing and Installing the Lower Air Baffle	114
Removing the Lower Air Baffle	114
Installing the Lower Air Baffle	115
Installing and Removing the SAS Riser Board (optional)	116
Installing the SAS Riser Board	116
Removing the SAS Riser Board	117
Installing and Removing the Intel® RAID Activation Key and RAID DIMM	119
Installing the Intel® RAID Activation Key and RAID DIMM	119
Removing the Intel® RAID Activation Key and RAID DIMM	120
Installing and Removing the Intel® RAID Smart Battery AXXRSBBU4	122
Installing and Removing the CD-ROM / DVD-ROM Drive	122
Removing the CD-ROM / DVD-ROM Drive	122
Installing a CD-ROM / DVD-ROM Drive	124
Installing and Removing a 5 ¹-inch Peripheral Device	125
Installing a 5 ¹-inch Peripheral Device	126
Removing a 5 ¹-inch Peripheral Device	127
Servicing the Processors	128
Handling the Intel® Xeon® Processor MP	128
Installing and Removing a Processor Thermal Blank	129
Removing a Processor Thermal Blank	129
Installing a Processor Thermal Blank	130
Installing and Removing a Processor	131
Installing a Processor	131
Removing a Processor	133
Removing and Installing the Center Brace	134
Removing the Center Brace	134
Installing the Center Brace	135
Installing and Removing the I/O Riser Board	136
Installing the I/O Riser Board	136
Removing the I/O Riser Board	136
Installing and Removing the Intel® Remote Management Module 2 (Intel® RMM2)	137
Installing the Intel® RMM2 and NIC Module	137
Removing the Intel® RMM2 and NIC Module	139
Replacing the Main Board	140
Removing the Main Board	140
Installing the Main Board	142
Replacing the SAS Backplane Board	145
Removing the SAS Backplane Board	145
Installing the SAS Backplane Board	146
Replacing the Power Distribution Board	146
Removing the Power Distribution Board	146
Installing the Power Distribution Board	148
Replacing the Front Panel Board	149
Removing the Front Panel Board	149
Installing the Front Panel Board	150
Replacing the CMOS Battery	151
Appendix A: POST Codes	155
POST Progress Codes and Messages	155
POST Error Messages and Handling	159
POST Error Beep Codes	171
Appendix B: Installation / Assembly Safety Instructions	173
English	173
Deutsch	175
Français	177
Español	179
Italiano	181
Appendix C: Safety Information	185
English	185
Server Safety Information	185
Safety Warnings and Cautions	185
Intended Application Uses	186
Site Selection	186
Equipment Handling Practices	187
Power and Electrical Warnings	187
System Access Warnings	188
Rack Mount Warnings	189
Electrostatic Discharge (ESD)	189
Other Hazards	190
Sicherheitshinweise für den Server	192
Sicherheitshinweise und Vorsichtsmaßnahmen	192
Zielbenutzer der Anwendung	193
Standortauswahl	193
Handhabung von Geräten	194
Warnungen zu Netzspannung und Elektrizität	194
Warnhinweise für den Systemzugang	195
Warnhinweise für Racks	196
Elektrostatische Entladungen (ESD)	196
Andere Gefahren	197
Français	198
Consignes de sécurité sur le serveur	198
Sécurité: avertissements et mises en garde	198
Domaines d’utilisation prévus	199
Sélection d’un emplacement	199
Pratiques de manipulation de l’équipement	199
Alimentation et avertissements en matière d’électricité	200
Avertissements sur l’accès au système	201
Avertissements sur le montage en rack	202
Décharges électrostatiques (ESD)	202
Autres risques	203
Información de seguridad del servidor	204
Advertencias y precauciones sobre seguridad	204
Aplicaciones y usos previstos	205
Selección de la ubicación	205
Manipulación del equipo	205
Advertencias de alimentación y eléctricas	206
Advertencias el acceso al sistema	207
Advertencias sobre el montaje en bastidor	208
Descarga electrostática (ESD)	208
Appendix D: Regulatory and Compliance Information	215
Product Regulatory Compliance	215
Product Safety Compliance	215
Product EMC Compliance - Class A Compliance	215
Certifications / Registrations / Declarations	216
Product Regulatory Compliance Markings	216
Electromagnetic Compatibility Notices	218
FCC Verification Statement (USA)	218
Industry Canada (ICES-003)	219
Europe (CE Declaration of Conformity)	219
VCCI (Japan)	219
BSMI (Taiwan)	220
RRL (Korea)	220
CNCA (CCC China)	220
Regulated Specified Components	221
Restriction of Hazardous Substances (RoHS) Compliance	221
End of Life / Product Recycling	222
Appendix E: Equipment Log	223
Appendix F: Warranty	225
Limited Warranty for Intel® Chassis Subassembly Products	225
Extent of Limited Warranty	226
Warranty Limitations and Exclusions	226
Limitations of Liability	226
How to Obtain Warranty Service	227
Telephone Support	227
Returning a Defective Product	227
Appendix G: Getting Help	229
World Wide Web	229

Match case Limit results 1 per page

Intel® Server System S7000FC4UR Product Guide

Cooling Subsystem

Caution:

The chassis top cover must be installed for proper system cooling. Cooling components

must be hot-swapped within two minutes. This time period applies only to the time that the

cooling component is physically removed, not from the time of failure.

The cooling subsystem consists of hot-swap, redundant (7+1) fans. In a redundant

configuration, the system supports one fault at a time, either one fan fault or one power

supply fault, and it supports hot-swapping one component at a time. If a cooling

component fails, the system cooling is maintained and the system continues to operate

while the component is hot-swapped.

Each front fan assembly has one status LED. The LED is off when both fans are operating

normally. The LED illuminate amber if one or both of the fans fails. Failed front fans can

be hot-swapped from the front of the system.

Each rear fan has one status LED. The LED is off when the fan is operating normally and

illuminates amber if the fan fails. Failed rear fans can be replaced from the top of the

system when the top cover is removed.

Figure 9. Rear Fan Locations

AF002242