Epson Stylus COLOR 850N User Manual - Page 107

Initializing the Ethernet Card, Configuring for DLC on Windows NT 4. 0

Get Epson Stylus COLOR 850N - Ink Jet Printer PDF manuals and user guides View all Epson Stylus COLOR 850N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

Using the Ethernet Card Caution: Don't use an outlet controlled by a wall switch or timer, or one that uses the same circuit as a large appliance. This may disrupt the power, which can erase memory or even damage the power supply. Initializing the Ethernet Card You only need to initialize the card under the following conditions:  The first time you connect the printer to a network.  EPSON Net! cannot recognize the card because its settings are incorrect.  You reinstall the card in a different printer. To initialize the card, make sure the printer is turned off (the power button should be up) and plug the printer into a properly grounded outlet while pressing down the status sheet button for at least three seconds. status sheet button To reset all card configuration settings to their factory defaults, turn the printer on while pressing the status sheet button on the card plate. Configuring for DLC on Windows NT 4.0 If you use Windows NT 4.0, the Ethernet card works with the DLC (Data Link Control) protocol provided in your operating system. Follow the instructions below to install DLC protocol and configure the Ethernet card to use it. 6-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
Using the Ethernet Card
6-5
Initializing the Ethernet Card
You only need to initialize the card under the following
conditions:
The first time you connect the printer to a network.
EPSON Net! cannot recognize the card because its settings
are incorrect.
You reinstall the card in a different printer.
To initialize the card, make sure the printer is turned off (the
power button should be up) and plug the printer into a properly
grounded outlet while pressing down the status sheet button for
at least three seconds.
To reset all card configuration settings to their factory defaults,
turn the printer on while pressing the status sheet button on the
card plate.
Configuring for DLC on
Windows NT 4.0
If you use Windows NT 4.0, the Ethernet card works with the
DLC (Data Link Control) protocol provided in your operating
system. Follow the instructions below to install DLC protocol
and configure the Ethernet card to use it.
Caution:
Don’t use an outlet
controlled by a wall switch
or timer, or one that uses
the same circuit as a large
appliance. This may
disrupt the power, which
can erase memory or
even damage the power
supply.
status sheet button