HP 630n HP Jetdirect Print Servers - Administrator's Guide - Page 153

DLC/LLC protocol information, Error messages

Get HP 630n - JetDirect Gigabit EN Print Server PDF manuals and user guides
UPC - 808736806244
View all HP 630n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 153 highlights

DLC/LLC protocol information Information in this section of the HP Jetdirect configuration page is described in Table 8-13 DLC/LLC configuration information on page 143. Table 8-13 DLC/LLC configuration information Message Description STATUS: Current DLC/LLC protocol status. READY Print server is awaiting data. DISABLED Manually disabled. INITIALIZING Registering the node address or name. Additional status messages might display. An error code and message is displayed if the print server is not ready. For more information, see Table 8-14 Error messages on page 143. Error messages Error codes and messages that might appear in the Status sections of the HP Jetdirect configuration page are described in Table 8-14 Error messages on page 143. Table 8-14 Error messages Error Code and Message Description 02 LAN ERROR - INTERNAL LOOPBACK During self-test, an internal loopback test error was detected. The print server might be faulty. If the error persists, replace the HP Jetdirect print server. 03 LAN ERROR - EXTERNAL LOOPBACK Print server is incorrectly connected to your network or is defective. Make sure it is correctly attached to your network by checking the cabling and connectors. 05 NO SIGNAL DETECTED (802.11 Wireless, Infrastructure Mode only) The print server did not find an access point and did not detect a radio signal. Check for sources of radio signal interference. If possible, elevate the print server or the external antenna (if applicable). Verify other wireless devices are turned on and located in wireless signal range of the print server. 06 ENCRYPTION REQUIRED Encryption is required on this network, but the encryption settings are incorrect. Check the encryption settings. 07 LAN ERROR - CONTROLLER CHIP Check the network connections. If they are intact, run the self-test by turning the printer off, and then on again. If the error persists, replace the HP Jetdirect print server. 07 AUTHENTICATION FAILED Print server could not access the network because of an authentication error. The error depends on the authentication method used. Verify the authentication method and settings. 08 LAN ERROR - INFINITE DEFERRAL Network congestion problem. 08 AUTHENTICATION IN PROGRESS Link-level authentication is in progress. 09 SCANNING FOR SSID (802.11 Wireless) The print server is scanning on all channels for devices on the specified SSID (network name). Check your specified SSID, or check status of the access point (Infrastructure mode) or other wireless devices. ENWW HP Jetdirect configuration page 143

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
DLC/LLC protocol information
Information in this section of the HP Jetdirect configuration page is described in
Table
8
-
13
DLC/LLC
configuration information
on page
143
.
Table 8-13
DLC/LLC
configuration information
Message
Description
STATUS:
Current DLC/LLC protocol status.
READY
Print server is awaiting data.
DISABLED
Manually disabled.
INITIALIZING
Registering the node address or name. Additional status messages might
display.
An error code and message is displayed if the print server is not ready. For more
information, see
Table
8
-
14
Error messages
on page
143
.
Error messages
Error codes and messages that might appear in the Status sections of the HP Jetdirect configuration
page are described in
Table
8
-
14
Error messages
on page
143
.
Table 8-14
Error messages
Error Code and Message
Description
02 LAN ERROR - INTERNAL
LOOPBACK
During self-test, an internal loopback test error was detected. The print server might be
faulty. If the error persists, replace the HP Jetdirect print server.
03 LAN ERROR - EXTERNAL
LOOPBACK
Print server is incorrectly connected to your network or is defective. Make sure it is
correctly attached to your network by checking the cabling and connectors.
05 NO SIGNAL DETECTED
(802.11 Wireless, Infrastructure Mode only) The print server did not find an access point
and did not detect a radio signal.
Check for sources of radio signal interference. If possible, elevate the print server or the
external antenna (if applicable). Verify other wireless devices are turned on and located
in wireless signal range of the print server.
06 ENCRYPTION REQUIRED
Encryption is required on this network, but the encryption settings are incorrect. Check
the encryption settings.
07 LAN ERROR - CONTROLLER
CHIP
Check the network connections. If they are intact, run the self-test by turning the printer
off, and then on again. If the error persists, replace the HP Jetdirect print server.
07 AUTHENTICATION FAILED
Print server could not access the network because of an authentication error. The error
depends on the authentication method used.
Verify the authentication method and settings.
08 LAN ERROR - INFINITE
DEFERRAL
Network congestion problem.
08 AUTHENTICATION IN
PROGRESS
Link-level authentication is in progress.
09 SCANNING FOR SSID
(802.11 Wireless) The print server is scanning on all channels for devices on the
specified SSID (network name). Check your specified SSID, or check status of the
access point (Infrastructure mode) or other wireless devices.
ENWW
HP Jetdirect configuration page
143