HP 630n HP Jetdirect Print Servers - Administrator's Guide - Page 62

Snmp Traps, Ipx/spx, En_8022, En_ii - jetdirect 635n print server

Get HP 630n - JetDirect Gigabit EN Print Server PDF manuals and user guides
UPC - 808736806244
View all HP 630n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Table 3-3 Telnet Commands and Parameters (continued) SNMP Traps auth-trap Send SNMP authentication traps. Authentication traps indicate that an SNMP request was received, but the community name check failed. 0 Disable. 1 (default) Enable. trap-dest Add a host's IP address to the HP Jetdirect print server's SNMP trap destination list. The list can contain up to six entries. To receive SNMP traps, the listed systems must have a trap daemon that listens for the traps. The following is the command format: trap-dest: [community name] [port number] In the example, is the IP address of the host to receive traps, [community name] specifies the SNMP community name, and [port number] identifies the port number to use. The default community name is public. The default SNMP port number is 162. You must enter a community name to specify a port number. To delete the list, set trap destination to zero (trap-dest: 0). By default, the SNMP trap destination list is empty and the print server does not send SNMP traps. IPX/SPX ipx-config IPX/SPX protocol operation on the print server. 0 Disable. 1 (default): Enable. NOTE: On HP Jetdirect 635n print servers, all network protocols except TCP/IP are disabled by factory default. ipx-unitname Name assigned to the print server. Enter up to 31 alphanumeric characters. By default, the name is NPIxxxxxx, where xxxxxx are the last six digits of the LAN hardware address. Address (Read-only parameter.) The IPX network and node numbers detected on the network, in the form :. ipx-frametype IPX frame type settings available for your print server model: AUTO (default), EN_SNAP, EN_8022, EN_8023, EN_II. For more information, see HP Jetdirect configuration pages on page 129. ipx-sapinterval Time in seconds that the HP Jetdirect print server waits between service advertising protocol (SAP) broadcasts on the network. Set from 1 to 3600 seconds. 0: Disable. 60 (default): Enable SAP broadcasts. ipx-mode (Read-only parameter.) NetWare mode configured on the print server (RPRINTER or QSERVER). ipx-nds-tree NDS tree name for the print server. Enter up to 31 alphanumeric characters. ipx-nds-context NDS context for the HP Jetdirect print server. Enter up to 256 alphanumeric characters. ipx-job-poll Specifies the time interval in seconds that the HP Jetdirect print server waits to check for print jobs in a print queue. Set from 1 to 255 seconds. 0: Disable. 52 Chapter 3 TCP/IP configuration ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
SNMP Traps
auth-trap
Send SNMP authentication traps. Authentication traps indicate that an SNMP request was
received, but the community name check failed.
0
Disable.
1
(default) Enable.
trap-dest
Add a host's IP address to the HP Jetdirect print server's SNMP trap destination list. The
list can contain up to six entries. To receive SNMP traps, the listed systems must have a
trap daemon that listens for the traps. The following is the command format:
trap-dest: <ip-address> [community name] [port number]
In the example,
<ip-address>
is the IP address of the host to receive traps,
[community name]
specifies the SNMP community name, and
[port number]
identifies the port number to use.
The default community name is public. The default SNMP port number is 162. You must
enter a community name to specify a port number.
To delete the list, set trap destination to zero (
trap-dest: 0
).
By default, the SNMP trap destination list is empty and the print server does not send
SNMP traps.
IPX/SPX
ipx-config
IPX/SPX protocol operation on the print server.
0
Disable.
1
(default): Enable.
NOTE:
On HP Jetdirect 635n print servers, all network protocols except TCP/IP are
disabled by factory default.
ipx-unitname
Name assigned to the print server. Enter up to 31 alphanumeric characters. By default,
the name is NPIxxxxxx, where xxxxxx are the last six digits of the LAN hardware address.
Address
(Read-only parameter.) The IPX network and node numbers detected on the network, in
the form <network number>:<LAN hardware address>.
ipx-frametype
IPX frame type settings available for your print server model:
AUTO
(default),
EN_SNAP,
EN_8022, EN_8023, EN_II
. For more information, see
HP Jetdirect configuration
pages
on page
129
.
ipx-sapinterval
Time in seconds that the HP Jetdirect print server waits between service advertising
protocol (SAP) broadcasts on the network. Set from 1 to 3600 seconds.
0
: Disable.
60
(default): Enable SAP broadcasts.
ipx-mode
(Read-only parameter.) NetWare mode configured on the print server (RPRINTER or
QSERVER).
ipx-nds-tree
NDS tree name for the print server. Enter up to 31 alphanumeric characters.
ipx-nds-context
NDS context for the HP Jetdirect print server. Enter up to 256 alphanumeric characters.
ipx-job-poll
Specifies the time interval in seconds that the HP Jetdirect print server waits to check for
print jobs in a print queue. Set from 1 to 255 seconds.
0
: Disable.
Table 3-3
Telnet Commands and Parameters (continued)
52
Chapter 3
TCP/IP configuration
ENWW