Home » HP Manuals » Print Servers » HP 630n » Manual Viewer

HP 630n HP Jetdirect Print Servers - Administrator's Guide - Page 42

AppleTalk, DLC/LLC, Other Settings, 100TX HALF - firmware

UPC - 808736806244

Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Table 3-2 TFTP configuration file parameters (continued) ipx-frametype: IPX frame type setting available for your print server model. Set to AUTO (default), EN_SNAP, EN_8022, EN_8023, EN_II. ipx-sapinterval: Time in seconds that the HP Jetdirect print server waits between service advertising protocol (SAP) broadcasts on the network. The range is 1 to 3600 seconds. 0: Disable. 60 (default): Enable SAP broadcasts. ipx-nds-tree: Name of the Novell directory services (NDS) tree for this printer. ipx-nds-context: NDS context for the HP Jetdirect print server. Enter up to 256 alphanumeric characters. ipx-job-poll: Time in seconds that the HP Jetdirect print server waits to check for print jobs in a print queue. The range is 1 to 255 seconds. 0: Disable. 2 (default): Enable. pjl-banner: (or ipx-banner:) Print an IPX banner using the printer job language (PJL). 0: Disable. 1 (default): Enable banner pages. pjl-eoj: (or ipx-eoj:) IPX end-of-job notification. 0: Disable. 1 (default): Enable. pjl-toner-low: (or ipx-toner-low:) IPX toner-low notification. 0: Disable. 1 (default): Enable. AppleTalk appletalk: (or at-config:, ethertalk:) Use AppleTalk (EtherTalk) protocol operation on the print server. 0: Disable. 1 (default): Enable. NOTE: On HP Jetdirect 635n print servers, all network protocols except TCP/IP are disabled by factory default. DLC/LLC dlc/llc-config: (or dlc/llc:) Use DLC/LLC protocol operation on the print server. 0: Disable. 1 (default): Enable. NOTE: On HP Jetdirect 635n print servers, all network protocols except TCP/IP are disabled by factory default. Other Settings link-type: (For wired 10/100/1000T Ethernet.) Set the print server's link speed (10, 100, 1000 Mbps) and communication mode (Fullor Half-Duplex). The available link-speed depends on the print server model. The communication modes are: AUTO, 1000FULL, 100AUTO, 100FULL, 100HALF, 10FULL, 10HALF. For AUTO (default), the print server uses auto-negotiation to configure the highest link speed and communication mode allowed. If auto-negotiation fails, either 100TX HALF or 10TX HALF is set, depending on the detected link speed of the hub/switch port. (A 1000T half-duplex selection is not supported.) upgrade: Set the name and location of a firmware upgrade file for the HP Jetdirect print servers. 32 Chapter 3 TCP/IP configuration ENWW

Section	Page
Introducing the HP Jetdirect print server	11
Supported print servers	11
Supported network protocols	12
Security protocols	13
SNMP (IP and IPX)	13
HTTPS	13
Authentication	14
EAP/802.1X server-based authentication	14
IPsec/Firewall	14
Supplied manuals	15
HP support	15
HP online support	15
Firmware upgrades	15
Firmware installation tools	15
HP support by phone	16
Product registration	16
Product accessibility	16
HP software solutions summary	17
HP Install Network Printer Wizard (Windows)	18
Requirements	18
HP Jetdirect printer installer for UNIX	19
HP Web Jetadmin	19
System requirements	19
Install HP Web Jetadmin software	19
Verify HP Web Jetadmin installation and provide access	20
Configure and modify a device	20
Remove HP Web Jetadmin software	20
Internet Printer Connection software	20
HP-supplied software	21
HP software system requirements	21
HP software supported proxies	21
Microsoft-supplied software	21
Windows 2000/XP/Server 2003 integrated software	21
Novell-supplied software	22
Mac OS network installation	22
TCP/IP configuration	25
IPv6 configuration	25
IPv6 address introduction	25
IPv6 address configuration	26
Link-local address	26
Stateless addresses	27
Stateful addresses	27
Use DNS	27
Tools and utilities	28
IPv4 configuration	28
Server-based and manual TCP/IP configuration (IPv4)	28
Default IP address (IPv4)	29
Default IP address is not assigned	29
Default IP address is assigned	29
Default IPv4 address configuration options	30
Default IPv4 behavior	30
TCP/IP configuration tools	31
Use BOOTP/TFTP (IPv4)	32
Advantages of using BOOTP/TFTP	32
Configure the print server using BOOTP/TFTP on UNIX	32
Use DHCP (IPv4)	44
UNIX systems	44
Windows systems	44
Discontinue DHCP configuration	46
Use RARP (IPv4)	46
Use the arp and ping commands (IPv4)	47
Use Telnet (IPv4)	48
Create a Telnet connection	49
A typical Telnet session	49
Telnet user interface options	50
Use Telnet to remove an IP address	67
Move to another network (IPv4)	68
Use the embedded Web server	68
Use the printer control panel	68
Embedded Web server (V.38.xx)	71
Requirements	72
Compatible Web browsers	72
Supported HP Web Jetadmin version	72
View the embedded Web server	73
Operating notes	74
HP Jetdirect Home tab	75
Device tabs	76
Networking tab	76
TCP/IP Settings	79
Summary tab	80
Network Identification tab	80
TCP/IP(v4) tab	81
TCP/IP(v6) tab	82
Config Precedence tab	83
Advanced tab	84
Network Settings	86
IPX/SPX	86
AppleTalk	87
DLC/LLC	87
SNMP	88
Other Settings	89
Misc. Settings	89
Firmware Upgrade	91
LPD Queues	91
USB Settings	93
Support Info	94
Refresh Rate	94
Select Language	94
Security: Settings	94
Status	94
Wizard	95
Restore Defaults	96
Authorization	97
Admin. Account	97
Certificates	97
Configure certificates	98
Access Control	100
Mgmt. Protocols	101
Web Mgmt.	101
SNMP	102
SNMP v3	102
Other	102
802.1X Authentication	103
IPsec/Firewall	104
Network Statistics	105
Protocol Info	105
Configuration Page	105
Other Links	105
? (Help)	105
Support	105
IPsec/Firewall configuration (V.38.xx)	107
Default Rule example	110
IPsec security associations (SA)	110
HP Jetdirect IPsec/Firewall wizard	110
Limitations to rules, templates and services	111
Step 1: Specify Address Template	112
Create Address Template	112
Step 2: Specify Service Template	113
Create Service Template	113
Manage Services	113
Manage Custom Services	114
Step 3: Specify Action	115
Specify IPsec/Firewall Template	115
Create IPsec Template	115
Identity Authentication	116
Kerberos	117
Kerberos Settings	117
IKEv1 Phase 1 (Authentication)	118
IKEv1 Phase 2 / Quick Mode (IPsec Protocols)	118
Advanced IKE Settings	119
IPsec Protocols (Manual Keys)	120
Manual Keys	120
Rule Summary	121
Configure Windows systems	121
Security features (V.38.xx)	123
Limit access to security features	126
Troubleshoot the HP Jetdirect print server	127
Reset to factory defaults	128
Example: Cold reset using the service menu	128
Disable an HP Jetdirect embedded print server (V.38.xx)	130
General troubleshooting	131
Troubleshooting chart - assess the problem	131
Procedure 1: Verify the printer is on and online	132
Procedure 2: Print an HP Jetdirect configuration page	132
Procedure 3: Resolve printer display error messages	133
Procedure 4: Resolve printer network communication problems	134
Troubleshooting wireless print servers	136
HP Jetdirect configuration pages	139
HP Jetdirect configuration page	140
Status field error messages	140
Configuration page format	140
Configuration page messages	141
HP Jetdirect Configuration/General Information	141
Security Settings	145
Network Statistics	147
TCP/IP protocol information	147
IPv4 section	148
IPv6 section	150
IPX/SPX protocol information	150
Novell/NetWare parameters	151
AppleTalk protocol information	152
DLC/LLC protocol information	153
Error messages	153
HP Jetdirect Security page	159
Security settings	160
IPsec Error Log	162
Local IP addresses	162
IPsec Statistics	162
IKE Stats	163
IPsec Rules	163
IPsec Security Associations (SA) table	163
Available Network Services	164
LPD printing	165
About LPD	166
Requirements for configuring LPD	166
LPD setup overview	167
Step 1. Set up IP parameters	167
Step 2. Set up print queues	167
Step 3. Print a test file	167
LPD on UNIX systems	167
Configure print queues for BSD-based systems	167
Use SAM to configure print queues (HP-UX systems)	169
Print a test file	170
LPD on Windows 2000/Server 2003 systems	170
Install TCP/IP software	170
Configure a network printer for Windows 2000/Server 2003 systems	171
Verify the configuration	172
Print from Windows clients	173
LPD on Windows XP systems	173
Add Windows optional networking components	173
Configure a network LPD printer	173
Add a new LPD printer	173
Create an LPR port for an installed printer	174
FTP printing	175
Requirements	175
Print files	175
Use FTP printing	175
FTP connections	175
Control connection	175
Data connection	176
FTP login	176
End the FTP session	177
Commands	177
Example FTP Session	178
HP Jetdirect control panel menus (V.38.xx)	179
Graphical control panel menus	180
Classic control panel EIO menus	187
Open source licensing statements	191
gSOAP	191
OpenSSL	192
OpenSSL license	192
Original SSLeay license	192

Match case Limit results 1 per page

ipx-frametype:

IPX frame type setting available for your print server model. Set to

AUTO

(default),

EN_SNAP

EN_8022

EN_8023,

EN_II

ipx-sapinterval:

Time in seconds that the HP Jetdirect print server waits between service advertising protocol (SAP) broadcasts on the

network. The range is 1 to 3600 seconds.

: Disable.

(default): Enable SAP broadcasts.

ipx-nds-tree:

Name of the Novell directory services (NDS) tree for this printer.

ipx-nds-context:

NDS context for the HP Jetdirect print server. Enter up to 256 alphanumeric characters.

ipx-job-poll:

Time in seconds that the HP Jetdirect print server waits to check for print jobs in a print queue. The range is 1 to 255

seconds.

: Disable.

(default): Enable.

pjl-banner:

(or

ipx-banner:

)

Print an IPX banner using the printer job language (PJL).

: Disable.

(default): Enable banner pages.

pjl-eoj:

(or

ipx-eoj:

)

IPX end-of-job notification.

: Disable.

(default): Enable.

pjl-toner-low

(or

ipx-toner-low

IPX toner-low notification.

: Disable.

(default): Enable.

AppleTalk

appletalk:

(or

at-config:

ethertalk:

)

Use AppleTalk (EtherTalk) protocol operation on the print server.

: Disable.

(default): Enable.

NOTE:

On HP Jetdirect 635n print servers, all network protocols except TCP/IP are disabled by factory default.

DLC/LLC

dlc/llc-config:

(or

dlc/llc:

)

Use DLC/LLC protocol operation on the print server.

: Disable.

(default): Enable.

NOTE:

On HP Jetdirect 635n print servers, all network protocols except TCP/IP are disabled by factory default.

Other Settings

link-type:

(For wired 10/100/1000T Ethernet.) Set the print server's link speed (10, 100, 1000 Mbps) and communication mode (Full-

or Half-Duplex). The available link-speed depends on the print server model. The communication modes are:

AUTO

1000FULL

100AUTO

100FULL

100HALF

10FULL

10HALF

For

AUTO

(default), the print server uses auto-negotiation to configure the highest link speed and communication mode

allowed. If auto-negotiation fails, either

100TX HALF

10TX HALF

is set, depending on the detected link speed of the

hub/switch port. (A 1000T half-duplex selection is not supported.)

upgrade:

Set the name and location of a firmware upgrade file for the HP Jetdirect print servers.

Table 3-2

TFTP configuration file parameters (continued)

Chapter 3

TCP/IP configuration

ENWW