HP 630n HP Jetdirect Print Servers - Administrator's Guide - Page 59

Enable. Restore factory default TCP/IP settings., ftp-download, ttl-slp, ipv4-multicast, idle-timeout

Get HP 630n - JetDirect Gigabit EN Print Server PDF manuals and user guides
UPC - 808736806244
View all HP 630n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Table 3-3 Telnet Commands and Parameters (continued) 7 through 12: If user-specified LPD queues are defined, corresponds to user-specified LPD queues 5 through 10. Although the default selection depends on the printer, it is typically Port 9100 printing or LPD binps. ftp-download Download firmware upgrade files to the print server, using FTP. 0: Disable. 1 (default): Enable. ttl-slp IP multicast time-to-live (TTL) setting for SLP packets. The default value is 4 hops (the number of routers from the local network). Set from 1 to 15 hops. -1: Disable. 4 (default): Enable multicast TTL. ipv4-multicast Receive and transmit IP version 4 multicast packets by the print server. 0: Disable. 1 (default): Enable. NOTE: If disabled, other protocols that use multicast protocols, such as Bonjour and SLP, might also be disabled without notification. idle-timeout Seconds that an idle print data connection can remain open. Set from 1 to 3600 seconds. 0: Disable. Connection does not terminate. Other hosts cannot make a connection. 270 (default): Enable. user-timeout Seconds that a Telnet or FTP session is idle before it is automatically disconnected. Set from 1 to 3600 seconds. 0: Disable. 900 (default): Enable. CAUTION: Setting this to a short time period might disable Telnet/FTP, because a session could terminate before changes can be made. cold-reset Reset to TCP/IP factory default settings after a cold reset. (Parameters for other subsystems, such as IPX/SPX or AppleTalk, are not affected.) 0: Disable. Retain TCP/IP settings after a cold reset. 1: Enable. Restore factory default TCP/IP settings. ews-config Allow use of the print server's embedded Web server. 0 Disable. 1 (default): Enable. For more information, see Embedded Web server (V.38.xx) on page 61. web-refresh Time interval for embedded Web server diagnostic page updates. Set from 1 to 99999 seconds. 0: Disable. tcp-mss Maximum segment size (MSS) that the HP Jetdirect print server advertises for use when communicating with local subnets (Ethernet MSS=1460 bytes or more) or remote subnets (MSS=536 bytes). ENWW IPv4 configuration 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
7
through
12
: If user-specified LPD queues are defined, corresponds to user-specified
LPD queues 5 through 10.
Although the default selection depends on the printer, it is typically Port 9100 printing or
LPD binps.
ftp-download
Download firmware upgrade files to the print server, using FTP.
0
: Disable.
1
(default): Enable.
ttl-slp
IP multicast time-to-live (TTL) setting for SLP packets. The default value is 4 hops (the
number of routers from the local network). Set from 1 to 15 hops.
-1
: Disable.
4
(default): Enable multicast TTL.
ipv4-multicast
Receive and transmit IP version 4 multicast packets by the print server.
0
: Disable.
1
(default): Enable.
NOTE:
If disabled, other protocols that use multicast protocols, such as Bonjour and SLP,
might also be disabled without notification.
idle-timeout
Seconds that an idle print data connection can remain open. Set from 1 to 3600 seconds.
0
: Disable. Connection does not terminate. Other hosts cannot make a connection.
270
(default): Enable.
user-timeout
Seconds that a Telnet or FTP session is idle before it is automatically disconnected. Set
from 1 to 3600 seconds.
0
: Disable.
900
(default): Enable.
CAUTION:
Setting this to a short time period might disable Telnet/FTP, because a
session could terminate before changes can be made.
cold-reset
Reset to TCP/IP factory default settings after a cold reset. (Parameters for other
subsystems, such as IPX/SPX or AppleTalk, are not affected.)
0
: Disable. Retain TCP/IP settings after a cold reset.
1
: Enable. Restore factory default TCP/IP settings.
ews-config
Allow use of the print server's embedded Web server.
0
Disable.
1
(default): Enable.
For more information, see
Embedded Web server (V.38.xx)
on page
61
.
web-refresh
Time interval for embedded Web server diagnostic page updates. Set from 1 to 99999
seconds.
0
: Disable.
tcp-mss
Maximum segment size (MSS) that the HP Jetdirect print server advertises for use when
communicating with local subnets (Ethernet MSS=1460 bytes or more) or remote subnets
(MSS=536 bytes).
Table 3-3
Telnet Commands and Parameters (continued)
ENWW
IPv4 configuration
49