HP 630n HP Jetdirect Print Servers - Administrator's Guide - Page 90

Miscellaneous Settings continued, Table 4-13

Get HP 630n - JetDirect Gigabit EN Print Server PDF manuals and user guides
UPC - 808736806244
View all HP 630n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Table 4-13 Miscellaneous Settings (continued) Item Description HP XML Services Allow access by HP Web service applications to XML-based data on the HP Jetdirect print server. Certificate Mgmt Service Allow HP Web Jetadmin to access and service your certificate configuration. Web Services Print Use the Microsoft Web Services for Devices (WSD) Print services supported on the HP Jetdirect print server. WS-Discovery Use the Microsoft Web Services Dynamic Discovery (WS Discovery) protocols on the print server. LLMNR Indicates whether link local multicast name resolution (LLMNR) requests are responded to over IPv4 and IPv6. Link settings (For wired 10/100/1000T Ethernet) Set the print server's link speed and communication mode. The available selections depend on the print server model. CAUTION: If you change the link setting, network communications with the print server and network device might be lost. ● AUTO (default) Use auto-negotiation to configure itself with the highest link speed and communication mode allowed. If auto-negotiation fails, either 100TX HALF or 10TX HALF is set, depending on the detected link speed of the hub/switch port. (A 1000T half-duplex selection is not supported.) ● 10T-Full 10 Mbps, full-duplex operation. ● 10T-Half 10 Mbps, half-duplex operation. ● 100TX-Full 100 Mbps, full-duplex operation. ● 100TX-Half 100 Mbps, half-duplex operation. ● 100TX-AUTO Limit auto-negotiation to a maximum link speed of 100 Mbps. ● 1000T FULL 1000 Mbps, full-duplex operation. Locally Administered Address (Supported print servers only) Warning: Changing the locally administered address results in the loss of connectivity to the browser. Specify a locally administered address (LAA) to replace the factory assigned LAN Hardware (MAC) address. If used, enter a string of exactly 12 hexadecimal digits. For Ethernet print servers, the LAA address must start with hexadecimal X2, X6, XA, or XE, where X is any hexadecimal digit 0 through F. The default address is the factory assigned address. Syslog Facility Identify the source facility of a message. Typically used to identify the source of selected messages during troubleshooting. By default, the HP Jetdirect print server uses LPR as the source facility code. However, you can use values of local0 through local7 to isolate individual or groups of print servers. HTTP Idle Timeout Length of time after which an idle HTTP connection is closed. Applies to the time after an HTTP request or response completes. Enter from 5 to 60 seconds. The default is 15. Set to zero (0) to disable. (The TCP/IP idle timeout value is used.) Dynamic Raw Port Setting Specify additional ports for printing to TCP port 9100. Valid ports are 3000 to 9000, which are application-dependent. Bonjour Highest Priority Service Specify the highest Bonjour priority service to use for printing: 9100 Printing Raw IP printing through HP-proprietary port 9100. 80 Chapter 4 Embedded Web server (V.38.xx) ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
Item
Description
HP XML Services
Allow access by HP Web service applications to XML-based data on the HP Jetdirect print
server.
Certificate Mgmt Service
Allow HP Web Jetadmin to access and service your certificate configuration.
Web Services Print
Use the Microsoft Web Services for Devices (WSD) Print services supported on the
HP Jetdirect print server.
WS-Discovery
Use the Microsoft Web Services Dynamic Discovery (WS Discovery) protocols on the print
server.
LLMNR
Indicates whether link local multicast name resolution (LLMNR) requests are responded
to over IPv4 and IPv6.
Link settings
(For wired 10/100/1000T Ethernet) Set the print server's link speed and communication
mode. The available selections depend on the print server model.
CAUTION:
If you change the link setting, network communications with the print server
and network device might be lost.
●
AUTO
(default) Use auto-negotiation to configure itself with the highest link speed
and communication mode allowed. If auto-negotiation fails, either 100TX HALF or
10TX HALF is set, depending on the detected link speed of the hub/switch port. (A
1000T half-duplex selection is not supported.)
●
10T-Full
10 Mbps, full-duplex operation.
●
10T-Half
10 Mbps, half-duplex operation.
●
100TX-Full
100 Mbps, full-duplex operation.
●
100TX-Half
100 Mbps, half-duplex operation.
●
100TX-AUTO
Limit auto-negotiation to a maximum link speed of 100 Mbps.
●
1000T FULL
1000 Mbps, full-duplex operation.
Locally Administered Address
(Supported print servers only) Warning: Changing the locally administered address results
in the loss of connectivity to the browser.
Specify a locally administered address (LAA) to replace the factory assigned LAN
Hardware (MAC) address. If used, enter a string of exactly 12 hexadecimal digits.
For Ethernet print servers, the LAA address must start with hexadecimal X2, X6, XA, or
XE, where X is any hexadecimal digit 0 through F.
The default address is the factory assigned address.
Syslog Facility
Identify the source facility of a message. Typically used to identify the source of selected
messages during troubleshooting. By default, the HP Jetdirect print server uses LPR as
the source facility code. However, you can use values of local0 through local7 to isolate
individual or groups of print servers.
HTTP Idle Timeout
Length of time after which an idle HTTP connection is closed. Applies to the time after an
HTTP request or response completes. Enter from 5 to 60 seconds. The default is 15.
Set to zero (0) to disable. (The TCP/IP idle timeout value is used.)
Dynamic Raw Port Setting
Specify additional ports for printing to TCP port 9100. Valid ports are 3000 to 9000, which
are application-dependent.
Bonjour Highest Priority
Service
Specify the highest Bonjour priority service to use for printing:
9100 Printing
Raw IP printing through HP-proprietary port 9100.
Table 4-13
Miscellaneous Settings (continued)
80
Chapter 4
Embedded Web server (V.38.xx)
ENWW