HP 630n HP Jetdirect Print Servers - Administrator's Guide - Page 189

Classic control panel EIO menus

Get HP 630n - JetDirect Gigabit EN Print Server PDF manuals and user guides
UPC - 808736806244
View all HP 630n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 189 highlights

Table C-2 HP Jetdirect EIO Menu on Classic Control Panel (continued) Menu Item Description IPSEC or (Full featured print servers only) If the print server supports IPsec, IPSEC is displayed on the menu for both IPsec and Firewall status. If the print server does not support IPsec, Firewall is displayed. Specify the state of IPsec/Firewall on the print server. FIREWALL Disable IPsec/Firewall. KEEP (default): Retain IPsec/Firewall operation as configured. DISABLE: Disable IPsec/Firewall operation. 802.1X KEEP (default): Retain current 802.1X settings. RESET: Reset 802.1X settings to factory defaults. PRINT Print a configuration page for the selected item. PROTOCOLS: Print IPX/SPX, Novell NetWare, AppleTalk,or DLC/LLC configuration. SECURITY: Print the current security settings. CFG LINK Manually configure the HP Jetdirect print server's network link. NO (default): Bypass the link configuration menu. YES: Access the link configuration menu. Set the link speed and communication mode. These must match the network. The available settings depend on the print server model. CAUTION: Changing the link setting can cause the loss of network communication with the print server. AUTO (default): Use auto-negotiation to set the highest link speed and communication mode allowed. If auto-negotiation fails, either 100TX HALF or 10TX HALF is set depending on the detected link speed of the hub/switch port. (A 1000T half-duplex selection is not supported.) 10T HALF: 10 Mbps, half-duplex operation. 10T FULL: 10 Mbps, Full-duplex operation. 100TX HALF: 100 Mbps, half-duplex operation. 100TX FULL: 100 Mbps, full-duplex operation. 100TX AUTO: Limits auto-negotiation to a maximum link speed of 100 Mbps. 1000 FULL: 1000 Mbps, full-duplex operation. ENWW Classic control panel EIO menus 179

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
Menu Item
Description
IPSEC
or
FIREWALL
(Full featured print servers only) If the print server supports IPsec, IPSEC is displayed on the
menu for both IPsec and Firewall status. If the print server does not support IPsec, Firewall is
displayed. Specify the state of IPsec/Firewall on the print server.
Disable IPsec/Firewall.
KEEP
(default): Retain IPsec/Firewall operation as configured.
DISABLE
: Disable IPsec/Firewall operation.
802.1X
KEEP
(default): Retain current 802.1X settings.
RESET
: Reset 802.1X settings to factory defaults.
PRINT
Print a configuration page for the selected item.
PROTOCOLS
: Print IPX/SPX, Novell NetWare, AppleTalk,or DLC/LLC configuration.
SECURITY
: Print the current security settings.
CFG LINK
Manually configure the HP Jetdirect print server's network link.
NO
(default): Bypass the link configuration menu.
YES
: Access the link configuration menu.
Set the link speed and communication mode. These must match the network. The available
settings depend on the print server model.
CAUTION:
Changing the link setting can cause the loss of network communication with the
print server.
AUTO
(default): Use auto-negotiation to set the highest link speed and communication mode
allowed. If auto-negotiation fails, either 100TX HALF or 10TX HALF is set depending on the
detected link speed of the hub/switch port. (A 1000T half-duplex selection is not supported.)
10T HALF
: 10 Mbps, half-duplex operation.
10T FULL
: 10 Mbps, Full-duplex operation.
100TX HALF
: 100 Mbps, half-duplex operation.
100TX FULL
: 100 Mbps, full-duplex operation.
100TX AUTO
: Limits auto-negotiation to a maximum link speed of 100 Mbps.
1000 FULL
: 1000 Mbps, full-duplex operation.
Table C-2
HP Jetdirect EIO Menu on Classic Control Panel (continued)
ENWW
Classic control panel EIO menus
179