IBM TS2340 User Guide - Page 153
Configuring IBM tape devices with AMCC FC HBAs, update_drv, reboot -- -r, opt/IBMtape/tapelist -l
UPC - 883436006873
View all IBM TS2340 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 153 highlights
Solaris Device Driver (IBMtape) IBMtape "scsiclass,01.vIBM.pXXX" for tape drive. IBMtape "scsiclass,08.vIBM.pXXX" for medium changer. Where: 01 and 08 stand for the type of tape drive and medium changer and XXX is the product ID string in the standard inquiry data. For example, ULT3580-TD2 is the product ID of the IBM LTO2 drive. The following entry is added in the file for the IBM LTO2 drive: IBMtape "scsiclass,01.vIBM.pULT3580-TD2" The following is a list of the entries for the supported IBM tape devices. For the tape drives: IBMtape "scsiclass,01.vIBM.pULT3580-TD1" IBMtape "scsiclass,01.vIBM.pULTRIUM-TD1" IBMtape "scsiclass,01.vIBM.pULT3580-TD2" IBMtape "scsiclass,01.vIBM.pULTRIUM-TD2" IBMtape "scsiclass,01.vIBM.pULT3580-TD3" IBMtape "scsiclass,01.vIBM.pULTRIUM-TD3" IBMtape "scsiclass,01.vIBM.pULT3580-HH3" IBMtape "scsiclass,01.vIBM.pULTRIUM-HH3" IBMtape "scsiclass,01.vIBM.pULT3580-TD4" IBMtape "scsiclass,01.vIBM.pULTRIUM-TD4" IBMtape "scsiclass,01.vIBM.p03592J1A" IBMtape "scsiclass,01.vIBM.p03592E05" IBMtape "scsiclass,01.vIBM.p03592E06" For the medium changers: IBMtape "scsiclass,08.vIBM.p03584L32" IBMtape "scsiclass,08.vIBM.p03584L22" IBMtape "scsiclass,08.vIBM.pULT3582-TL" IBMtape "scsiclass,08.vIBM.pULT3583-TL" IBMtape "scsiclass,08.vIBM.pULT3581-TA" IBMtape "scsiclass,08.vIBM.pULT3581-TA2" IBMtape "scsiclass,08.vIBM.p3576-MTL" IBMtape "scsiclass,08.vIBM.p3573-TL" IBMtape "scsiclass,08.vIBM.p3577-TL" Note: The entry is also added running the # update_drv command on Solaris 8 (patch 111804-03 is required), Solaris 9, and later versions of the operating system. For example: # update_drv -av -i '"scsiclass,01.vIBM.pULT3580-TD2"' IBMtape 6. Reboot the system by running # reboot -- -r. 7. Run # /opt/IBMtape/tapelist -l to display the configured tape device information. Note: All of the added entries are removed by the operating system automatically after IBMtape is unloaded from the kernel by running the # pkgrm, rem_drv, or modunload commands. It is strongly recommended that you back up these entries in a file, and that you re-enter the entries when you upgrade the IBMtape driver before running the #pkgadd command. Configuring IBM tape devices with AMCC FC HBAs To configure an IBM tape device with an AMMC FC HBA, complete the following steps: 1. Modify and add the following parameters in /kernel/drv/jnic146x.conf: CmdTaskAttr=1; lun_throttle=1; tape-device="IBMtape"; tape-changer="IBMtape"; 2. Update the change in jnic146x.conf. Chapter 6. Solaris Tape and Medium Changer Device Driver 135