Kenwood TS-990S Operation Manual - Page 13

TABLE OF CONTENTS ADJUSTING THE EFFECT OF THE SPEECH PROCESSOR 9-7 TRANSMIT FILTER 9-8 SELECTING A TX FILTER 9-8 CHANGING THE NUMBER OF AVAILABLE TX FILTERS 9-8 CHANGING THE BANDWIDTH OF THE TX FILTER 9-9 TX DSP EQUALIZER 9-9 SWITCHING THE TX DSP EQUALIZER ON OR OFF 9-9 SELECTING THE FREQUENCY CHARACTERISTICS OF THE TX DSP EQUALIZER 9-10 ADJUSTING THE TX DSP EQUALIZER 9-10 COPYING THE CONFIGURATION DATA FOR THE TX DSP EQUALIZER 9-11 SAVING THE CONFIGURATION DATA FOR THE TX DSP EQUALIZER 9-12 READING THE CONFIGURATION DATA FOR THE TX DSP EQUALIZER 9-12 DISPLAYING THE SUBSCOPE DURING TX 9-13 TX TUNING 9-14 TOGGLING BETWEEN TRANSMISSION AND RECEPTION EACH TIME THE KEY IS PRESSED: TX TUNE 1 9-14 ACTIVATING TRANSMISSION ONLY WHILE THE KEY IS PRESSED: TX TUNE 2 9-14 ADJUSTING THE TRANSMIT POWER FOR TX TUNING 9-14 TIME-OUT TIMER (TOT 9-15 10 MEMORY CHANNELS MEMORY CHANNEL 10-1 DISPLAYING THE MEMORY CHANNEL LIST 10-1 CONFIGURING THE OPERATING DATA TO A MEMORY CHANNEL.... 10-2 CONFIGURING THE OPERATING DATA TO A SINGLE-BAND MEMORY CHANNEL 10-2 CONFIGURING THE OPERATING DATA TO A DUAL-BAND MEMORY CHANNEL 10-3 CONFIGURING OPERATING DATA BY DIRECTLY ENTERING A FREQUENCY 10-3 MEMORY CHANNEL MODE 10-4 OPERATING IN SINGLE-BAND MEMORY CHANNEL MODE 10-4 OPERATING IN DUAL-BAND MEMORY CHANNEL MODE 10-4 SELECTING A MEMORY CHANNEL 10-5 DIRECTLY ENTERING THE MEMORY CHANNEL NUMBER 10-5 TEMPORARILY CHANGING THE OPERATING DATA 10-5 TEMPORARILY CHANGING THE FREQUENCY 10-5 COPYING OPERATING DATA FROM THE MEMORY CHANNEL.... 10-6 MEMORY SHIFT (MEMORY TO VFO 10-6 COPYING OPERATING DATA FROM ONE MEMORY CHANNEL TO ANOTHER MEMORY CHANNEL (CHANNEL TO CHANNEL 10-6 CONFIGURING THE PROGRAM SCAN FREQUENCY RANGE...... 10-7 CLEARING THE MEMORY CHANNEL 10-7 CONFIGURING NAMES FOR MEMORY CHANNELS 10-7 QUICK MEMORY 10-8 QUICK MEMORY CHANNELS 10-8 CONFIGURING IN QUICK MEMORY 10-8 RECALLING QUICK MEMORY CHANNELS 10-8 CONFIGURING THE NUMBER OF QUICK MEMORY CHANNELS.... 10-9 CLEARING QUICK MEMORY CHANNELS 10-9 MEMORY SHIFT (QUICK MEMORY TO VFO 10-9 11 SCAN PROGRAM SCAN 11-1 STARTING THE PROGRAM SCAN (VFO SCAN 11-1 CONFIGURING THE PROGRAM SCAN (VFO SCAN) FREQUENCY RANGE 11-1 CHANGING THE SCAN SPEED 11-2 SCAN HOLD 11-2 PROGRAM SLOW SCAN 11-3 ENABLING OR DISABLING THE PROGRAM SLOW SCAN 11-3 CONFIGURING THE PROGRAM SLOW SCAN FREQUENCY POINT.... 11-3 CONFIGURING THE PROGRAM SLOW SCAN FREQUENCY RANGE....11-4 MEMORY SCAN 11-4 STARTING THE SCAN 11-4 EXAMPLES OF CONFIGURATIONS FOR THE ALL CHANNEL SCAN AND THE GROUP SCAN 11-4 LOCKING OUT A MEMORY CHANNEL 11-5 QUICK MEMORY SCAN 11-6 RESUMING THE SCANNING 11-6 12 ABOUT THE USB FLASH DRIVE ABOUT THE USB FLASH DRIVE 12-1 FORMATTING A USB FLASH DRIVE 12-1 SAFELY REMOVING THE USB FLASH DRIVE 12-1 SAVING A FILE IN USB FLASH DRIVE 12-2 READING A FILE FROM USB FLASH DRIVE 12-2 DELETING A FILE FROM USB FLASH DRIVE 12-3 CHANGING A FILE NAME IN THE USB FLASH DRIVE 12-4 13 VOICE MESSAGE AND AUDIO FILE RECORDING AND PLAYING VOICE MESSAGE 13-1 RECORDING A VOICE MESSAGE 13-1 NAMING A VOICE MESSAGE 13-2 PLAYING A VOICE MESSAGE 13-2 ADJUSTING THE VOLUME OF VOICE MESSAGE 13-3 TRANSMITTING A VOICE MESSAGE 13-3 CLEARING A VOICE MESSAGE 13-4 CONFIGURING INTERVAL TIME FOR RETRANSMIT 13-4 RECORDING AND PLAYING COMMUNICATION AUDIO 13-4 CONFIGURING THE SAVE DESTINATION OF AUDIO FILE 13-4 MANUAL RECORDING 13-5 FULL-TIME RECORDING 13-5 CONFIGURING THE MAXIMUM TIME FOR FULL-TIME RECORDING.....13-5 SAVING AUDIO WITH FULL-TIME RECORDING 13-6 PLAYING AN AUDIO FILE 13-6 ADJUSTING THE VOLUME OF VOICE MESSAGE 13-6 AUDIO FILES 13-7 COPYING AUDIO FILE FROM INTERNAL MEMORY TO USB FLASH DRIVE 13-7 PLAYING AN AUDIO FILE 13-7 NAMING AN AUDIO FILE 13-8 DELETING AN AUDIO FILE 13-9 PROTECTING AN AUDIO FILE FROM DELETION (ONLY FOR INTERNAL MEMORY 13-10 14 VOICE GUIDANCE VOICE GUIDANCE 14-1 CONFIGURING THE VOLUME OF THE VOICE GUIDANCE 14-1 CONFIGURING THE VOICE GUIDANCE SPEED 14-1 CONFIGURING THE ANNOUNCEMENT LANGUAGE 14-1 AUTOMATICALLY ANNOUNCING VOICE GUIDANCE 14-2 VOICE 1 14-3 VOICE 2 14-10 VOICE 3 14-10 15 CLOCK DISPLAY AND TIMER CONFIGURING THE DATE AND TIME 15-1 CONFIGURING THE DATE FOR THE LOCAL CLOCK 15-1 CONFIGURING THE TIME FOR THE LOCAL CLOCK 15-1 CONFIGURING THE TIMEZONE FOR THE LOCAL CLOCK 15-2 CONFIGURING THE TIMEZONE FOR THE SECONDARY CLOCK......15-2 CONFIGURING AN IDENTIFICATION LETTER FOR THE SECONDARY CLOCK 15-2 CONFIGURING THE DATE DISPLAY FORMAT 15-2 CORRECTING THE CLOCK WITH NTP (NETWORK TIME PROTOCOL 15-3 CONFIGURING THE NTP SERVER ADDRESS 15-3 ENABLING OR DISABLING THE AUTOMATIC TIME CORRECTION....15-4 MANUAL CLOCK CORRECTION 15-4 TIMER 15-5 CONFIGURING THE PROGRAMMABLE TIMER 15-5 TEMPORARILY DISABLING THE TIMER TASK 15-6 SLEEP TIMER 15-7 CONFIGURING THE SLEEP TIMER 15-7 DISABLING THE POWER-OFF BY THE SLEEP TIMER 15-7 APO (AUTOMATIC POWER OFF 15-7 16 USEFUL FUNCTIONS CONFIGURING THE POWER-ON MESSAGE 16-1 CONFIGURING THE SCREEN SAVER 16-1 CONFIGURING THE SCREEN SAVER TYPE 16-1 CONFIGURING THE SCREEN SAVER WAIT TIME 16-2 Index XI