Kenwood TS-990S Operation Manual - Page 204

Configuring The Program Slow Scan Frequency Range, Memory Scan, Starting The Scan

Get Kenwood TS-990S PDF manuals and user guides View all Kenwood TS-990S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 204 highlights

11 SCAN CONFIGURING THE PROGRAM SLOW SCAN FREQUENCY RANGE The scan time for Program Scan while the transceiver slows down the scanning on the frequency points for Program Slow Scan and its adjacent frequency range. This adjacent frequency range is called the frequency range. Follow the procedure below to configure the frequency range for the slow scan frequency. 1 Select Group No. 4, "Memory Channels & Scan", from the Menu screen. 2 Access Menu 03, "Program Slow Scan Range". 3 Press [SELECT] (F4) to allow editing of the parameter box. 4 Press [-] (F4) or [+] (F5), or rotate the MULTI/CH control to select "100 [Hz]", or "200 [Hz]", "300 [Hz]", "400 [Hz]", or "500 [Hz]". • The default is "300 [Hz]". • For instance, if "500 [Hz]" is selected, the transceiver slows down the scanning at the frequency point within ±500 Hz of the frequency range. 5 Press [ ] (F1). 6 Press [MENU] to exit. MEMORY SCAN Memory Scan enables the transceiver to change the preconfigured Memory Channels at certain time intervals for scanning. There are two Memory Scans: All Channel Scan which scans all Memory Channels to which the operating data has been stored, and Group Scan which scans the selected and grouped Memory Channels. STARTING THE SCAN 1 Press [M/V] while in VFO mode to enter Single-band Memory Channel mode, or press and hold [M/V] to enter Dual-band Memory Channel mode. 2 Press [SCAN] (F5) to activate Memory Scan. • Rotating the MULTI/CH control fast-forwards or fastreverses the scanning sequence. • Pressing [SCAN] (F5) again or pressing [ESC] stops the Memory Scan. Note: ◆◆Memory Scan stops if the transceiver receives a signal on the main band or sub band while in Dual-band Memory Channel mode. ◆◆The scan time for each frequency during Memory Scan is 400 ms. However, if the transceiver receives a CTCSS tone in FM mode, the scan time is extended to 600 ms. "SCANNING" appears in place of the scan speed. EXAMPLES OF CONFIGURATIONS FOR THE ALL CHANNEL SCAN AND THE GROUP SCAN 1 Press [M/V] while in VFO mode to enter Single-band Memory Channel mode, or press and hold [M/V] to enter Dual-band Memory Channel mode. 2 Press and hold [SCAN] (F5) to open the Program Scan screen. 11-4 Index Contents

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
11 SCAN
11-4
Index
Contents
CONFIGURING THE PROGRAM SLOW SCAN
FREQUENCY RANGE
The scan time for Program Scan while the transceiver
slows down the scanning on the frequency points for
Program Slow Scan and its adjacent frequency range. This
adjacent frequency range is called the frequency range.
Follow the procedure below to configure the frequency
range for the slow scan frequency.
1
Select Group No. 4, "Memory Channels & Scan", from
the
Menu
screen.
2
Access Menu 03, "Program Slow Scan Range".
3
Press
[SELECT]
(F4) to allow editing of the parameter
box.
4
Press
[-]
(F4) or
[+]
(F5), or rotate the
MULTI/CH
control to select "100 [Hz]", or "200 [Hz]", "300 [Hz]",
"400 [Hz]", or "500 [Hz]".
•
The default is "300 [Hz]".
•
For instance, if "500 [Hz]" is selected, the transceiver slows
down the scanning at the frequency point within ´500 Hz of
the frequency range.
5
Press
[
]
(F1).
6
Press
[MENU]
to exit.
MEMORY SCAN
Memory Scan enables the transceiver to change the
preconfigured Memory Channels at certain time intervals
for scanning.
There are two Memory Scans: All Channel Scan which
scans all Memory Channels to which the operating data
has been stored, and Group Scan which scans the
selected and grouped Memory Channels.
STARTING THE SCAN
1
Press
[M/V]
while in VFO mode to enter Single-band
Memory Channel mode, or press and hold
[M/V]
to
enter Dual-band Memory Channel mode.
2
Press
[SCAN]
(F5) to activate Memory Scan.
•
Rotating the
MULTI/CH
control fast-forwards or fast-
reverses the scanning sequence.
•
Pressing
[SCAN]
(F5) again or pressing
[ESC]
stops the
Memory Scan.
Note:
◆
Memory Scan stops if the transceiver receives a signal on the main
band or sub band while in Dual-band Memory Channel mode.
◆
The scan time for each frequency during Memory Scan is 400 ms.
However, if the transceiver receives a CTCSS tone in FM mode, the
scan time is extended to 600 ms. "SCANNING" appears in place of
the scan speed.
EXAMPLES OF CONFIGURATIONS FOR THE ALL
CHANNEL SCAN AND THE GROUP SCAN
[MULTI/CH]
[ESC]
[F1]~[F7]
[MR]
[M/V]
1
Press
[M/V]
while in VFO mode to enter Single-band
Memory Channel mode, or press and hold
[M/V]
to
enter Dual-band Memory Channel mode.
2
Press and hold
[SCAN]
(F5) to open the
Program
Scan
screen.