Kenwood TS-990S Operation Manual - Page 248

16 USEFUL FUNCTIONS List of Functions for Key Assignment Parameter MENU 0-00 : MENU 9-03 Advanced Operation and activation of function assigned Press to access a menu ranging from 0-00 to 9-03. For details, refer to "Menu". {page 3-2} Calls up or closes Advanced Menu No. 00 each time MENU 0 the key is pressed. : Advanced Calls up or closes Advanced Menu No. 30 each time MENU 30 the key is pressed. Press to tune the signal using and via the internal antenna tuner or leave the signal not tuned by AT/AT TUNE bypassing (through) the internal antenna tuner. Press and hold to begin tuning the internal antenna tuner. Press to toggle the VOX function between active and VOX/SEL inactive. Press and hold to open the VOX Level screen. Press to toggle the Speech Processor between PROC/SEL active and inactive. Press and hold to open the Speech Processor ANT1 ANT2 ANT3 ANT4 screen. Press to select ANT 1. Press to select ANT 2. Press to select ANT 3. Press to select ANT 4. Press to select Data 1. DATA 1/SEL Press and hold to open the Modulation Source screen. Press to select Data 2. DATA 2/SEL Press and hold to open the Modulation Source screen. Press to select Data 3. DATA 3/SEL Press and hold to open the Modulation Source screen. Press to place the transceiver, with the dual band RX (Main Band) in the receive state, in the receive state using the TX (Main Band) single band. Press to allow the transceiver to transmit using the main band frequency (Simplex). Press to copy the operating data such as the M>S main band frequency and operating mode to the operating data for the sub band. M/S Press to toggle the reception capability for the sub band between active and inactive. RX (Sub Band) Press to toggle the dual-band watch (reception) between ON and OFF. Press to configure the transmit functions to the sub band frequency and place the transceiver in split TX (Sub Band)/ (Split Frequency) mode. Press and hold to enable the configuration for split frequency. This is the default for Menu 28, "Microphone PF 1: TF-SET Key Assignment". While [TF-SET] is pressed down, the transceiver receives on the transmit frequency. Press to select the main band. MAIN This is the default for Menu 27, "Microphone PF 2: Key Assignment". Press to select the sub band. SUB This is the default for Menu 29, "Microphone PF 3: Key Assignment". Each time you press this key, the operating mode M/V (MEMORY) toggles between Memory Channel mode and VFO M.IN (MEMORY) mode. Press to toggle the memory scroll mode between active and inactive. The operating data configured for the Memory M>V (MEMORY) Channel will be copied to the VFO. This is the default for Menu 30, "Microphone PF 4: Key Assignment". Parameter Operation and activation of function assigned REC Each time you press this key, normal recording (RECORDER)/ starts. Full-time REC Press and hold to start constant recording. STOP (RECORDER) Press to stop recording or playback. PLAY (RECORDER) Press to play back the latest audio file recorded in normal or constant recording mode. Press this key during playback to pause. Each time you press this key, the display contents for the sub-screen changes. S.DISP/SEL Each time you press and hold this key, the highlighted display toggles between active and inactive. Each time you press this key, the Quick Memory MR (QUICK mode toggles between active and inactive. MEMO)/SEL Press and hold to clear all the operating data stored in Quick Memory Channels. M.IN (QUICK MEMO) Press to save data in Quick Memory Channels. CW T. (Main Band) Press to activate CW auto tuning for the main band. FIL A/SEL (Main Press to select RX Filter A for the main band. Band) Press and hold to open the Receive Filter screen. FIL B/SEL (Main Press to select RX Filter B for the main band. Band) Press and hold to open the Receive Filter screen. FIL C/SEL (Main Press to select RX Filter C for the main band. Band) Press and hold to open the Receive Filter screen. AGC SEL (Main Band) Press to open the AGC screen for the main band. The transceiver does not respond if you press and hold this PF key. AGC SLOW (Main Press to select "Slow" for the Automatic Gain Band) Control speed for the main band. AGC MID (Main Press to select "Medium" for the Automatic Gain Band) Control speed for the main band. AGC FAST (Main Press to select "Fast" for the Automatic Gain Control Band) speed for the main band. AGC OFF (Main Press to disable the Automatic Gain Control for the Band) main band. NCH SEL (Main Band) Press to select either narrow or wide for the notch filter bandwidth. The transceiver does not respond if you press and hold this PF key. A.NCH SEL (Main Band) Press to open the Auto Notch Filter screen. The transceiver does not respond if you press and hold this PF key. BEF SEL (Main Band) Press to open the Band Elimination Filter screen for the main band. The transceiver does not respond if you press and hold this PF key. APF SEL (Main Band) Press to open the Audio Peak Filter screen for the main band. The transceiver does not respond if you press and hold this PF key. MUTE (Main Band) Press to mute the audio for the main band. CW T. (Sub Band) Press to start CW auto tuning for the sub band. FIL A/SEL (Sub Press to select RX Filter A for the sub band. Band) Press and hold to open the Receive Filter screen. FIL B/SEL (Sub Press to select RX Filter B for the sub band. Band) Press and hold to open the Receive Filter screen. FIL C/SEL (Sub Press to select RX Filter C for the sub band. Band) Press and hold to open the Receive Filter screen. AGC/SEL (Sub Band) Press to open the AGC screen for the sub band. The transceiver does not respond if you press and hold this PF key. AGC SLOW (Sub Press to select "Slow" for the Automatic Gain Band) Control speed for the sub band. AGC MID (Sub Press to select "Medium" for the Automatic Gain Band) Control speed for the sub band. AGC FAST (Sub Press to select "Fast" for the Automatic Gain Control Band) speed for the sub band. AGC OFF (Sub Press to disable the Automatic Gain Control for the Band) sub band. 16-8 Index Contents