Kenwood TS-990S Operation Manual - Page 249

Parameter Operation and activation of function assigned NCH SEL (Sub Band) Press to select either narrow or wide for the notch filter bandwidth for the sub band. The transceiver does not respond if you press and hold this PF key. A.NCH/SEL (Sub Band) Press to open the Auto Notch Filter screen. The transceiver does not respond if you press and hold this PF key. BEF SEL (Sub Band) Press to open the Band Elimination Filter screen for the sub band. The transceiver does not respond if you press and hold this PF key. NB1 SEL (Sub Band) Press to open the Noise Blanker 1 (Sub Band) screen. The transceiver does not respond if you press and hold this PF key. NB2 SEL (Sub Band) Press to open the Noise Blanker 2 (Sub Band) screen. The transceiver does not respond if you press and hold this PF key. Press and hold to open the Noise Reduction NR1 SEL (Sub 1 (Sub Band) screen for the sub band. The Band) transceiver does not respond if you press and hold this PF key. Press and hold to open the Noise Reduction NR2 SEL (Sub 2 (Sub Band) screen for the sub band. The Band) transceiver does not respond if you press and hold this PF key. APF SEL (Sub Band) Press to open the Audio Peak Filter screen for the sub band. The transceiver does not respond if you press and hold this PF key. MUTE (Sub Band) Press to mute the audio of the sub band. Press to enable the voice guidance of the main band VOICE 1 (Main frequency. Band) This is the default for Menu 17, "VOICE (Main Band): Key Assignment". Press to emit a voice guidance, such as a value for the signal strength of the selected band during VOICE 2 reception, and a value for transmit power during transmission. This is the default for Menu 15, "PF A Key: Key Assignment". Press to emit a voice guidance, such as a value of the selected with [METER] (F). The transceiver does VOICE 3 not emit the voice guidance during reception. This is the default for Menu 16, "PF B Key: Key Assignment". Press to enable the voice guidance of the sub band VOICE 1 (Sub frequency. Band) This is the default for Menu 18, "VOICE (Sub Band): Key Assignment". DSP MONITOR While you are holding down this key, the passband width of the IF filter is expanded to maximum. RX MONITOR While you are holding down this key, the squelch opens. TX TUNE1 Starts TX tuning when the key is pressed. TX TUNE2 Operates while the key is being pressed down. Press to transmit the signal entered via the DATA SEND modulation source (rear panel) configured for each audio source. Press to place the transceiver into a transmit state. SEND Press again to revert the transceiver to the original state. Each time you press this key, the modulation line DATA VOX/SEL cycles as follows: Off > ACC 2 > USB > OPT. Press and hold to open the Modulation Source screen. Press to transmit the Voice message, CW message, Message Memory FSK message, or PSK message stored in channel 1. CH1 This is the default for Menu 19, "External PF 1: Key Assignment". Press to transmit the Voice message, CW message, Message Memory FSK message, or PSK message stored in channel 2. CH2 This is the default for Menu 20, "External PF 2: Key Assignment". USEFUL FUNCTIONS 16 Parameter Operation and activation of function assigned Press to transmit the Voice message, CW message, Message Memory FSK message, or PSK message stored in channel 3. CH3 This is the default for Menu 21, "External PF 3: Key Assignment". Press to transmit the Voice message, CW message, Message Memory FSK message, or PSK message stored in channel 4. CH4 This is the default for Menu 22, "External PF 4: Key Assignment". Press to transmit the Voice message, CW message, Message Memory FSK message, or PSK message stored in channel 5. CH5 This is the default for Menu 23, "External PF 5: Key Assignment". Press to transmit the Voice message, CW message, Message Memory FSK message, or PSK message stored in channel 6. CH6 This is the default for Menu 24, "External PF 6: Key Assignment". Press to transmit the CW message, FSK message, Message Memory or PSK message stored in channel 7. CH7 This is the default for Menu 25, "External PF 7: Key Assignment". Press to transmit the CW message, FSK message, Message Memory or PSK message stored in channel 8. CH8 This is the default for Menu 26, "External PF 8: Key Assignment". CONTEST NUMBER DECREMENT Press to subtract the contest number by one. (CW Mode) SWL Press to place the transceiver into SWL mode. RF SCOPE Press to display the bandscope. AF SCOPE Press to display the audio scope. WATERFALL Press to display the waterfall. Extended Channel Memory Press to invoke the Extended Memory Channel. Press to operate the transceiver in the same DOWN Key (Microphone) manner as when the [DOWN] key of the optional microphone is pressed. This is the default for Menu 31, "Microphone DOWN: Key Assignment". Press to operate the transceiver in the same manner UP Key (Microphone) as when the [UP] key of the optional microphone is pressed. This is the default for Menu 32, "Microphone UP: Key Assignment". Press to capture the screen images in the main Capture screen and the sub-screen and save them as image files to a USB flash drive. Safe Removal of Press to execute Safe Removal of the USB Flash USB Flash Drive Drive. Emergency Press to call using the frequency allocated to notify Frequency the emergency call frequency on the main band. Off Nothing is activated. Contents Index 16-9