Kenwood TS-990S Operation Manual - Page 239

Sleep Timer, Configuring The Sleep Timer, Disabling The Power-off By The Sleep Timer

Get Kenwood TS-990S PDF manuals and user guides View all Kenwood TS-990S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 239 highlights

CLOCK DISPLAY AND TIMER 15 SLEEP TIMER The Sleep Timer is a function that turns the transceiver power ( ) OFF upon lapse of the configured length of time. CONFIGURING THE SLEEP TIMER DISABLING THE POWER-OFF BY THE SLEEP TIMER The timed power-off ( ) can be disabled even after the Sleep Timer has started counting down. If Sleep Time is temporarily disabled, the transceiver power ( ) does not turn OFF even when the configured time elapses. 1 Press [TIMER/SET]. The "TIMER" LED turns Off, and the timed power-off ( ) by Sleep Timer will be disabled. The Sleep Timer continues to count down; however, the transceiver power ( ) does not turn OFF even when the Sleep Timer expires. Pressing [TIMER/SET] again before the Sleep Timer expires causes the Sleep Timer to resume counting down from the remaining time. Note: ◆◆A press of [TIMER/SET] again disables or enables both the Sleep Timer and the Programmable Timer. 1 Press and hold [TIMER/SET] to open the Timer screen. 2 Press [ ] (F2) or [ "Sleep Timer". ] (F3) to select 3 Press [EDIT] (F4) to allow editing of the parameter box. APO (AUTOMATIC POWER OFF) APO is a function that turns the transceiver power ( ) OFF if no key or control is operated for the configured time. One minute before the transceiver power ( ) turns OFF, a Morse codes "CHECK" sounds from the speaker. 1 Select Group No. 0, "Basic Configurations", from the Menu screen. 2 Access Menu 33, "Automatic Power Off". 3 Press [SELECT] (F4) to allow editing of the parameter box. 4 Press [-] (F4) or [+] (F5), or the MULTI/CH control to select "Off" to turn the transceiver power ( ) OFF or the time until the transceiver power ( ) will be turned OFF. • You can select the length of time until the transceiver power ( ) will be turned OFF from "OFF" (do not turn the transceiver power ( ) OFF), "5", "10", "15", "30", "60", "90", and "120" [min]. The default is "Off". • Pressing and holding [(CLEAR)] (F1) resets the time configured for the Sleep Timer to its default. 5 Press [OK] (F6). • The "TIMER" LED lights green, and the Sleep Timer starts counting down. • Pressing [CANCEL] (F7) clears the entered parameter and reverts to the Clock screen. 6 Press [ESC] to exit. Note: ◆◆A message notifying you that the transceiver power ( ) is about to be turned OFF appears three minutes before and one minute before the transceiver power ( ) turns OFF. 4 Press [-] (F2) or [+] (F3) to select "OFF" or the length of time until the transceiver ( ) turns OFF. You can select the length of time until the transceiver power ( ) will be turned OFF from "OFF" (do not turn the transceiver power ( ) OFF), "60", "120", and "180" [min]. The default is "Off". 5 Press [ ] (F1). 6 Press [MENU] to exit. Note: ◆◆The timer for the APO continues counting down even during scan. ◆◆The transceiver starts counting down from when a key or a control is last operated. Contents Index 15-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
CLOCK DISPLAY AND TIMER 15
15-7
Index
Contents
SLEEP TIMER
The Sleep Timer is a function that turns the transceiver
power (
) OFF upon lapse of the configured length of
time.
[ TIMER/SET ]
[F1]~[F7]
[ ESC ]
[MULTI/CH]
[MENU]
CONFIGURING THE SLEEP TIMER
1
Press and hold
[TIMER/SET]
to open the
Timer
screen.
2
Press
[
]
(F2) or
[
]
(F3) to select
"Sleep Timer".
3
Press
[EDIT]
(F4) to allow editing of the parameter box.
4
Press
[-]
(F4) or
[+]
(F5), or the
MULTI/CH
control to
select "Off" to turn the transceiver power (
) OFF or
the time until the transceiver power (
) will be turned
OFF.
•
You can select the length of time until the transceiver
power (
) will be turned OFF from "OFF" (do not turn the
transceiver power (
) OFF), "5", "10", "15", "30", "60", "90",
and "120" [min]. The default is "Off".
•
Pressing and holding
[(CLEAR)]
(F1) resets the time
configured for the Sleep Timer to its default.
5
Press
[OK]
(F6).
•
The "TIMER" LED lights green, and the Sleep Timer starts
counting down.
•
Pressing
[CANCEL]
(F7) clears the entered parameter and
reverts to the
Clock
screen.
6
Press
[ESC]
to exit.
Note:
◆
A message notifying you that the transceiver power (
) is about
to be turned OFF appears three minutes before and one minute
before the transceiver power (
) turns OFF.
DISABLING THE POWER-OFF BY THE SLEEP TIMER
The timed power-off (
) can be disabled even after the
Sleep Timer has started counting down. If Sleep Time is
temporarily disabled, the transceiver power (
) does not
turn OFF even when the configured time elapses.
1
Press
[TIMER/SET]
.
The "TIMER" LED turns Off, and the timed power-off (
) by
Sleep Timer will be disabled. The Sleep Timer continues to
count down; however, the transceiver power (
) does not
turn OFF even when the Sleep Timer expires.
Pressing
[TIMER/SET]
again before the Sleep Timer expires
causes the Sleep Timer to resume counting down from the
remaining time.
Note:
◆
A press of
[TIMER/SET]
again disables or enables both the Sleep
Timer and the Programmable Timer.
APO (AUTOMATIC POWER OFF)
APO is a function that turns the transceiver power (
) OFF
if no key or control is operated for the configured time.
One minute before the transceiver power (
) turns OFF, a
Morse codes "CHECK" sounds from the speaker.
1
Select Group No. 0, "Basic Configurations", from the
Menu
screen.
2
Access Menu 33, "Automatic Power Off".
3
Press
[SELECT]
(F4) to allow editing of the parameter
box.
4
Press
[-]
(F2) or
[+]
(F3) to select "OFF" or the length
of time until the transceiver (
) turns OFF.
You can select the length of time until the transceiver
power (
) will be turned OFF from "OFF" (do not turn the
transceiver power (
) OFF), "60", "120", and "180" [min]. The
default is "Off".
5
Press
[
]
(F1).
6
Press
[MENU]
to exit.
Note:
◆
The timer for the APO continues counting down even during scan.
◆
The transceiver starts counting down from when a key or a control
is last operated.