Kenwood TS-990S Operation Manual - Page 295

Index A ABOUT FIRMWARE UPDATING 17-1 ABOUT THE GPL/LPGL LICENSE IV ABOUT THE USB FLASH DRIVE 12-1 ABOUT THIS MANUAL III ACC 2 CONNECTOR 1-11 ACCESSORIES CONNECTIONS (FRONT PANEL).........1-2 ACTIVATING AUDIO PEAK FILTER FOR USE IN CW MODE 6-7 ADJUSTING THE AF GAIN 4-7 ADJUSTING THE BEEP VOLUME 16-5 ADJUSTING THE MICROPHONE GAIN 4-18,5-14 ADJUSTING THE MICROPHONE GAIN FOR FM MODE OPERATION 5-32 ADJUSTING THE REFERENCE LEVEL 7-2 ADJUSTING THE RF GAIN 4-8 ADJUSTING THE RTTY THRESHOLD LEVEL OF PSK DECODING 5-55 ADJUSTING THE RTTY THRESHOLD LEVEL OF RTTY DECODING 5-41 ADJUSTING THE SIDETONE AND PITCH FREQUENCY 5-16 ADJUSTING THE SPEECH PROCESSOR INPUT LEVEL 9-6 ADJUSTING THE SQUELCH LEVEL 4-8 ADJUSTING THE TX POWER 4-19 AFC (Automatic Frequency Control 5-57 AGC (AUTOMATIC GAIN CONTROL 5-4 ANNOUNCE LANGUAGE CONFIGURATION 14-1 ANNOUNCE VOLUME CONFIGURATION 14-1 ANTENNA INSTALLTION AND CONNECTION 1-1 APO (AUTOMATIC POWER OFF 15-7 APPLYING THE UPPER LIMIT FREQUENCY OR LOWER LIMIT FREQUENCY FOR CENTER MODE TO FIX MODE 7-7 ATTENUATOR (ATT 6-1 AUDIO FILES 13-7 AUDIO PEAK FILTER WHILE IN FSK MODE 6-9 AUDIO SCOPE 8-1 AUDIO SCOPE SPAN WIDTH 8-2 AUDIO SOURCE LINES FOR TX AUDIO 5-11 AUTO ANNOUNCE CONFIGURATION 14-2 AUTO MODE 4-11 AUTO NOTCH FILTER (SSB 6-11 AUTO ZERO-IN (CW AUTO TUNE 5-17 AUTOMATICALLY CHANGING MODE FROM SSB FOR CW TRANSMISSION 5-18 AVERAGING THE WAVEFORM DISPLAY ON THE BANDSCOPE 7-9 B BAND ELIMINATION FILTER 6-12 BANDSCOPE 7-1 BEAT CANCELLER (SSB, AM AND FM 6-14 C CALBRATING THE INTERNAL REFERENCE FREQUENCY 18-1 CALIBRATION PROCEDURE 18-1 CAPTURING AND SAVING SCREEN IMAGES............16-12 CARRIER FREQUENCY OFFSET WHEN CHANGING FROM SSB MODE TO CW MODE 5-18 CENTER MODE 7-3 CHANGING A FILE NAME IN THE USB FLASH DRIVE....12-4 CHANGING THE AF FILTER TYPE 6-5 CHANGING THE ANTENNA 4-22 Contents MISCELLANEOUS 19 CHANGING THE ATTENUATOR FOR THE AUDIO SCOPE 8-1 CHANGING THE ATTENUATOR FOR THE BANDSCOPE 7-9 CHANGING THE AUDIO SCOPE FREQUENCY DISPLAY SPAN 8-2 CHANGING THE AUDIO SOURCE FOR THE AUDIO SCOPE 8-1 CHANGING THE CUTOFF FREQUENCIES (LOW AND HIGH FREQUENCIES) TO ADJUST THE PASSBAND WIDTH CHARACTERISTICS 6-6 CHANGING THE DISPLAYED FREQUENCY SPAN (CENTER MODE 7-3 CHANGING THE DISPLAY OF THE BANDSCOPE (MAIN BAND AND SUB-BAND 7-2 CHANGING THE IF FILTER BANDWIDTH CHARACTERISTICS 6-2 CHANGING THE LEVEL OF THE OSCILLOSCOPE........8-2 CHANGING THE NUMBER OF BAND MEMORIES.........4-9 CHANGING THE PASSBAND CHARACTERISTICS OF THE AUDIO PEAK FILTER (APF 6-8 CHANGING THE PASSBAND WIDTH AND AMOUNT OF SHIFT TO ADJUST PASSBAND CHARACTERISTICS.....6-7 CHANGING THE RECEIVE FREQUENCY USING YOUR FINGERTIP (CENTER MODE 7-5 CHANGING THE RECEIVE FREQUENCY USING YOUR FINGERTIP (FIX MODE 7-5 CHANGING THE SWEEP TIME 8-3 CLEARING A QUICK MEMORY CHANNEL 10-9 CLEARING THE MEMORY CHANNEL 10-7 CLOSING THE MENU 3-1 COM CONNECTOR 1-10 COMMON OPERATION IN THE MENU SCREEN............3-1 CONFIGURATION FOR PSK ENCODING AND DECODING 5-63 CONFIGURATION FOR RTTY ENCODING AND DECODING 5-46 CONFIGURING FOR THE ROOFING FILTER ADDED BY YOU (MAIN BAND ONLY 16-22 CONFIGURING IN QUICK MEMORY 10-8 CONFIGURING NAMES FOR MEMORY CHANNELS....10-7 CONFIGURING THE AFC TUNING RANGE 5-57 CONFIGURING THE AUTOMATIC TRANSMISSION AND RECEPTION FOR THE RTTY MESSAGE MEMORY....... 5-44 CONFIGURING THE AUTOMATIC TRANSMISSION AND RECEPTION USING THE RTTY MESSAGE MEMORY.... 5-45 CONFIGURING THE CARRIER LEVEL 5-14 CONFIGURING THE DATE AND TIME 15-1 CONFIGURING THE I/O SIGNALS FOR THE ACC 2 CONNECTOR 16-20 CONFIGURING THE I/O SIGNALS FOR THE OPTICAL DIGITAL CONNECTOR 16-19 CONFIGURING THE I/O SIGNALS FOR THE USB CONNECTOR 16-21 CONFIGURING THE LENGTH OF TIME FOR KEY LONG PRESS 16-5 CONFIGURING THE LOWER AND UPPER LIMIT...........7-6 CONFIGURING THE NETWORK 16-12 CONFIGURING THE NUMBER OF QUICK MEMORY CHANNELS 10-9 CONFIGURING THE OPERATING BAND 4-8 CONFIGURING THE OUTPUT TO AN EXTERNAL METER 16-15 CONFIGURING THE POLARITY FOR ACC 2 KEYING....5-50 CONFIGURING THE POWER-ON MESSAGE 16-1 19-3