Kenwood TS-990S Operation Manual - Page 287

TROUBLESHOOTING 18 Symptom Common Problem What to do Ref. Page The transmit power cannot exceed 100 W (TS-990S only). AT-300 is in use. While the AT-300 is in use, the transmit power is limited to 100 W. {page 1-9} The transmit power is limited to 100 W by Review in the Transmit Power screen the Max Power Limit. transmit power limit for normal transmission. {page 4-19} The transceiver retains the transmission even The transmission retain function when Disable the transmission retain function when after AT Tune has completed. the AT Tune has completed is enabled. the AT Tune has completed in Advanced Menu {page 4-25} 9. Frequencies for the main band and sub band Frequency tracking is enabled. jointly vary. Disable frequency tracking. {page 5-3} The frequency cannot be changed even with Fine Tuning is enabled. a rotation of the Tuning control. Disable Fine Tuning. {page 4-14} VFO Scan will not start. Program Scan has been configured, Deselect all to disable configurations for instead. Memory Channels P0 to P9 on the Program {page 11-1} Scan screen. Memory Scan will not start. No data is configured for the Memory Channels. Configure the Memory Channels. {page 10-2} Group Scan does not start. No data has been configured for the Memory Channels in the group. Configure the Memory Channels in the group. {page 11-4} All Memory Channels in a group are locked out. Unlock the Memory Channels to be scanned. {page 11-5} The transceiver scans the limited channels The channels not scanned allow the during Memory Scan. Group Memory Scan. Deselect the Group. {page 11-4} Voice Guidance does not automatically start. Auto Voice Guidance is disabled. Enable the Auto Voice Guidance. {page 14-2} The transceiver does not automatically emit Voice Guidance is disabled in Menu the Voice Guidance after the Full Reset. 1-06. With the transceiver power ( ) OFF, press [ ] while you are pressing down [PF A], or {page 14-2} select anything other than "Off" in Menu 1-06. It takes time to power up. You started up the transceiver by In such cases, even if Standby State Low pressing the main power switch (I/O) or Power Consumption is disabled, it may take {page 4-2} after you connect the AC power cable. time to power up. The transceiver is in Standby State Low Disable the Standby State Low Power Power Consumption mode. Consumption in Advanced Menu 22. {page 4-2} The cooling fan runs even after the Temperature on the final unit or the Cooling Fan remains running if the Cooling transceiver power turns OFF. power supply unit is high. Fan while the transceiver power turns OFF is enabled and temperature on the final unit and {page 4-3} the power supply unit is high. The "TIMER" LED blinks and you cannot turn Timed task by a timer is in preparation to Wait until the timed task by a timer will the transceiver ON. activate the timed task. activate. Press and hold [ ] for four seconds to cancel {page 15-5} the timed task by a timer. Timed task by Program Timer cannot be activated. The main power (I/O) is shut down. To use a timer, the main power switch (I/O) must remain in the "I" position. {page 4-1} The USB flash drive cannot be To use the timer recording function, use the distinguished. USB flash drive which was formatted by this transceiver and has sufficient remaining {page 12-1} memory. Timed task by a timer cannot be Be sure that the timed task by a timer is activated. properly in process so that the timed task by a timer is not temporarily suspended (the "TIMER" LED turns Off) by pressing [TIMER/ {page 15-5} SET] after the time task by a timer has been set. The frequency cannot be configured for the The transceiver is in Memory Channel Select VFO mode for both the main band and Program Timer. mode for the main band or sub band. the sub band in order to do configuration in {page 10-4} the Timer screen. The HI/LO control cannot be used. Disabled with the menu configuration. Select "Main and Sub Bands" in Menu 0-14. {page 16-4} The received audio sounds from one There is low volume level of the received Refer to chapters 16 to 19 to configure channel in a PC (the PC is connected to the audio sent from the USB terminal of the the transceiver itself and the level of the transceiver with a USB cable). transceiver or the audio entered to the microphone terminal of the PC. {page 16-1} microphone terminal of the PC. Monaural is configured in the PC for the If the OS in your PC is Windows Vista or later, microphone. select "2 Channels" from the Control Panel > Hardware and Sound > Sound > Recording > Microphone (USB Audio CODEC) > Advanced. The received audio sounds from one channel Monaural is configured in the PC for the If the OS in your PC is Windows Vista or later, in a PC (the PC is connected to the ACC 2 microphone. select "2 Channels" from the Control Panel > connector). Hardware and Sound > Sound > Recording > Microphone > Advanced. Contents Index 18-9