Kenwood TS-990S Operation Manual - Page 283
Safe Removal of USB Flash Drive failed. ERR: 005B, A DSP error was detected. ERR: 0068
View all Kenwood TS-990S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 283 highlights
TROUBLESHOOTING 18 ID Message Outline and What to do 0059 Failure in Deleting a File. (ERR: 0059) No reference signal has been detected. (ERR: 005A) 005A Ensure that the reference signal has been sourced to the REF I/O (10 MHz) connector. Safe Removal of USB Flash Drive failed. (ERR: 005B) Appears when deletion of a file fails. Be sure the USB flash drive is write protected. Appears when the reference signal from an external source cannot be detected. Be sure the signal is present at the REF I/O connector and that the signal level is sufficient. 005B The data file may not be stored onto the USB flash drive. Remove the USB flash drive after the main power (I/O) is shut Appears if the safe removal of the USB flash drive fails. Follow the instruction given on the error message. down. An error in the transmitter circuit has been detected. There is a Appears when over current is detected from the transmitter. possibility of failure. If this error message appears again even after turning off the main power 005C Refer to the list of messages in the instruction manual. (ERR: (I/O) or performing a full reset, there is a possibility of failure. Stop using, 005C) note the error message number (ERR: 005C), and contact a KENWOOD Transmission capability is disabled while this message appears. service center. The selected file cannot be read by this transceiver with the 005D earlier version firmware installed. (ERR: 005D) Update the transceiver firmware using the latest version of firmware. Appears if the transceiver attempts to read the configuration data which was created by the transceiver with newer firmware installed than that has been installed onto this transceiver. The file can be read after updating the transceiver firmware to the latest version. Corruption of the data was detected. (ERR: 005E) 005E Executing a Full Reset will initialize the transceiver to the defaults. Appears when damage is detected from the data for backup. Press [OK] (F) to start the Full Reset. Press [OK] (F) to start the Full Reset. Appears when an error was detected from a DSP used for reception and 0060 to 0063 A DSP error was detected. (ERR: 0060 to 0063) Refer to the list of messages in the instruction manual. transmission on the main band. This may be solved by shutting down the main power (I/O) or executing a Full Reset. If this error message frequently appears, note the error message number (ERR: 0060 to 0063), and contact a KENWOOD service center. Appears when an error was detected from a DSP used for reception on the 0064 to 0067 A DSP error was detected. (ERR: 0064 to 0067) Refer to the list of messages in the instruction manual. sub band. This may be solved by shutting down the main power (I/O) or executing a Full Reset. If this error message frequently appears, note the error message number 0068, 0069, A DSP error was detected. (ERR: 0068, 0069, 006A, 006B) 006A, Refer to the list of messages in the instruction manual. 006B (ERR: 0064 to 0067), and contact a KENWOOD service center. Appears when an error was detected from a DSP used for the bandscope. This may be solved by shutting down the main power (I/O) or executing a Full Reset. If this error message frequently appears, note the error message number (ERR: 0068, 0069, 006A, 006B), and contact a KENWOOD service center. An exceptional error occurs and the system stops. Shut down the main An unsolvable error occurs. Shut down the transceiver with the power switch (I/O). Update the transceiver firmware using the latest version main power switch (I/O), and then restart the transceiver after of firmware. a while. If this error message repeatedly appears, contact a KENWOOD service center. Contents Index 18-5