Konica Minolta AccurioPress C14000 Plockmatic PowerSquare R2L User Manual - Page 112

See Lubricate the Stitch Head on, See Lift the PowerSquare 224

Get Konica Minolta AccurioPress C14000 PDF manuals and user guides View all Konica Minolta AccurioPress C14000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

5 - Troubleshooting - Clear a Stitch Head Jam Step 1 2 Action Lift the PowerSquare 224 main deck. Remove the wire-holder from the stitch head. Information See "Lift the PowerSquare 224 Main Deck" on page 45. • Move the wire-holder retaining spring to the right. See Figure 55 on page 105. • Remove the wire-holder. • If the wire-holder is held in position, use a screw driver to help the removal of the wireholder from the stitch head. Caution: Do not apply force to the wire guide bars or the pivot block. See Figure 56. 3 Inspect the area behind the wire- See Figure 56 on page 105. holder for pieces of stitch-wire. 4 Remove any stitches or pieces of Use the wire-cutters to remove stitch-wire and clean the area with any jammed stitches or pieces of the air-duster. stitch-wire. 5 Lubricate the stitch-head. See "Lubricate the Stitch Head" on page 125. 6 Fit the wire-holder. Remember to put the wire-holder retaining spring in position. 7 Close the PowerSquare 224. 8 Start the PowerSquare 224. If the head operates normally and returns to the parked position, then further action is not needed. If the stitch head remains jammed, then repeat the procedure one time. If the problem continues, then contact your Plockmatic service engineer. 106 Plockmatic PowerSquare™224 User Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
5 - Troubleshooting - Clear a Stitch Head Jam
106
Plockmatic PowerSquare™224 User Manual
Step
Action
Information
1
Lift the PowerSquare 224 main
deck.
See “Lift the PowerSquare 224
Main Deck” on page 45.
2
Remove the wire-holder from the
stitch head.
•
Move the wire-holder retaining
spring to the right. See
Figure 55 on page 105.
•
Remove the wire-holder.
•
If the wire-holder is held in
position, use a screw driver to
help the removal of the wire-
holder from the stitch head.
Caution:
Do not apply force to the
wire guide bars or the pivot block.
See Figure 56.
3
Inspect the area behind the wire-
holder for pieces of stitch-wire.
See Figure 56 on page 105.
4
Remove any stitches or pieces of
stitch-wire and clean the area with
the air-duster.
Use the wire-cutters to remove
any jammed stitches or pieces of
stitch-wire.
5
Lubricate the stitch-head.
See “Lubricate the Stitch Head” on
page 125.
6
Fit the wire-holder.
Remember to put the wire-holder
retaining spring in position.
7
Close the PowerSquare 224.
8
Start the PowerSquare 224.
If the head operates normally and
returns to the parked position, then
further action is not needed.
If the stitch head remains jammed,
then repeat the procedure one
time.
If the problem continues, then con
-
tact your Plockmatic service engi
-
neer.