Konica Minolta AccurioPress C14000 Plockmatic PowerSquare R2L User Manual - Page 82

Side-Trimming problem - the book is not trimmed to the correct size

Get Konica Minolta AccurioPress C14000 PDF manuals and user guides View all Konica Minolta AccurioPress C14000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

5 - Troubleshooting - Book Quality Problems Side-Trimming problem - the book is not trimmed to the correct size Is SIDE TRIM turned on? Yes No Turn on the SIDE TRIM. Is the correct trim size entered in the touch screen? Make sure the size is at least 2mm less than the book size. Yes No Enter the correct size in the touch screen. Open and then close the top cover of the side-trimmer. Wait for the side-trimmer to reset. Does the problem continue? Yes No Further action is not needed. Turn off the Side-Trimmer at the mains ON/OFF switch. Wait for 5 seconds and then turn on the Side-Trimmer. Does the problem continue? Yes No Further action is not needed. Call your service engineer. Side-Trimming problem - the book is only trimmed on one side This problem is normally caused by incorrect set-up. If the side-trim offset is slightly too large, only one side is trimmed. Is AUTO turned off in the SIDE TRIM window? No Yes Set SIDE TRIM to AUTO. Does the problem continue? Yes No Further action is not needed. If you need to use a custom trim size, enter the trim dimension in the SIDE TRIM window. Make sure the size is at least 2mm less than the book size. Open and then close the top cover of the side-trimmer. Wait for the side-trimmer to reset. Does the problem continue? Yes No Further action is not needed. Turn off the Side-Trimmer at the mains ON/OFF switch. Wait for 5 seconds and then turn on the Side-Trimmer. Does the problem continue? Yes No Further action is not needed. Call your service engineer. 76 Plockmatic PowerSquare™224 User Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
5 - Troubleshooting - Book Quality Problems
76
Plockmatic PowerSquare™224 User Manual
Side-Trimming problem - the book is not trimmed to the correct size
Side-Trimming problem - the book is only trimmed on one side
This problem is normally caused by incorrect set-up.
If the side-trim offset is
slightly too large, only one side is trimmed.
Is
SIDE TRIM
turned on?
Yes
No
Turn on the
SIDE TRIM
.
Is the correct trim size entered in the touch screen? Make sure the size is at least
2mm less than the book size.
Yes
No
Enter the correct size in the touch screen.
Open and then close the top cover of the side-trimmer.
Wait for the side-trimmer
to reset.
Does the problem continue?
Yes
No
Further action is not needed.
Turn off the Side-Trimmer at the mains ON/OFF switch.
Wait for 5 seconds and
then turn on the Side-Trimmer.
Does the problem continue?
Yes
No
Further action is not needed.
Call your service engineer.
Is
AUTO
turned off in the
SIDE TRIM
window?
No
Yes
Set
SIDE TRIM
to
AUTO
.
Does the problem continue?
Yes
No
Further action is not needed.
If you need to use a custom trim size, enter the trim dimension in the
SIDE TRIM
window.
Make sure the size is at least 2mm less than the
book size.
Open and then close the top cover of the side-trimmer.
Wait for the side-trimmer
to reset.
Does the problem continue?
Yes
No
Further action is not needed.
Turn off the Side-Trimmer at the mains ON/OFF switch.
Wait for 5 seconds and
then turn on the Side-Trimmer.
Does the problem continue?
Yes
No
Further action is not needed.
Call your service engineer.