Konica Minolta AccurioPress C14000 Plockmatic PowerSquare R2L User Manual - Page 95

If a side trimmer, is installed, check, is switched on as, needed., SET IN GATHERING

Get Konica Minolta AccurioPress C14000 PDF manuals and user guides View all Konica Minolta AccurioPress C14000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

5 - Troubleshooting - Message List Message Information Reference SET IN GATHERING AREA Shuttle axis moving SHUTTLE MOTOR COMMS FAIL SHUTTLE MOTOR ERROR SHUTTLE - No comms SHUTTLE NOT PARKED Sidelay axis moving SIDELAY - No comms There is a set or partial set in the gathering area. Open the gathering area and remove the sheets. If the print job has been cancelled, open the gathering area and remove the sheets. Or touch START > ADVANCED > PURGE SET > PURGE SET to clear the set from the machine. If a side trimmer is installed, check the side trimmer is switched on as needed. See "The Side-Trimmer" on page 8. The shuttle axis is adjusting. This message clears when the adjustment is complete. If the message does not clear, touch ADVANCED > RE-REF. Use the mains ON/OFF switch. Turn the machine OFF, then turn the machine ON. If the problem continues, then call your service engineer. Use the mains ON/OFF switch. Turn the machine OFF, then turn the machine ON. If the problem continues, then call your service engineer. Use the mains ON/OFF switch. Turn the machine OFF, then turn the machine ON. If the problem continues, then call your service engineer. The shuttle is in the wrong position. Touch START, then follow the instructions on the screen. The sidelay axis (size adjustment) is adjusting. This message clears when the adjustment is complete. If the message does not clear, touch ADVANCED > RE-REF. Use the mains ON/OFF switch. Turn the machine OFF, then turn the machine ON. If the problem continues, then call your service engineer. Plockmatic PowerSquare™224 User Manual 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
5 - Troubleshooting - Message List
Plockmatic PowerSquare™224 User Manual
89
SET IN GATHERING
AREA
There is a set or partial set in the
gathering area.
Open the gathering area and
remove the sheets.
If the print job has been cancelled,
open the gathering area and
remove the sheets.
Or touch
START
>
ADVANCED
>
PURGE
SET
>
PURGE SET
to clear the set from
the machine.
If a side trimmer
is installed, check
the side trimmer
is switched on as
needed.
See “The
Side-Trimmer” on
page 8.
Shuttle axis moving
The shuttle axis is adjusting. This
message clears when the adjust
-
ment is complete.
If the message does not clear,
touch
ADVANCED
>
RE-REF
.
SHUTTLE MOTOR
COMMS FAIL
Use the mains ON/OFF switch.
Turn the machine OFF, then turn
the machine ON. If the problem
continues, then call your service
engineer.
SHUTTLE MOTOR
ERROR
Use the mains ON/OFF switch.
Turn the machine OFF, then turn
the machine ON.
If the problem
continues, then call your service
engineer.
SHUTTLE - No comms
Use the mains ON/OFF switch.
Turn the machine OFF, then turn
the machine ON. If the problem
continues, then call your service
engineer.
SHUTTLE NOT
PARKED
The shuttle is in the wrong posi
-
tion. Touch
START
, then follow the
instructions on the screen.
Sidelay axis moving
The sidelay axis (size adjustment)
is adjusting. This message clears
when the adjustment is complete.
If the message does not clear,
touch
ADVANCED
>
RE-REF
.
SIDELAY - No comms
Use the mains ON/OFF switch.
Turn the machine OFF, then turn
the machine ON. If the problem
continues, then call your service
engineer.
Message
Information
Reference