Panasonic AG-HPX600PJ Operating Instructions - Page 157
Warning system, Warnings description list
View all Panasonic AG-HPX600PJ manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 157 highlights
Warning system Chapter 10 Maintenance and Inspection - Warning system Warnings description list If an error is detected immediately after the camera turns on or during operation, the lamp and the lamp on the viewfinder screen indicate the error. Priority Warning type Viewfinder screen display 1 System error [SYSTEM ERROR] factor display*1 flashes in red. Tally lamp Flashes four times every second 2 P2 card removal [TURN POWER OFF] flashes error in red. Flashes four times every second [LOW BATTERY] flashes in red 3 Battery empty and an empty remaining battery indicator bar flashes. (Displayed even if its display setting is turned Flashes once every second off in the setting menu.) 4 P2 card fully recorded [ FULL] flashes in red. Flashes four times every second after the recording finishes 5 Recording error [REC WARNING] factor display*2 flashes in red. Flashes four times every second 6 Corruption of standard signal [TEMPORARY PAUSE IRREGULAR FRM SIG] flashes in red. Flashes four times every second Flashes four 7 Low wireless signal reception [WIRELESS RF] flashes in red. times every second (for recording only) One remaining battery indicator 8 Battery nearly empty bar flashes. (Also displayed when the [OTHER DISPLAY] item on the setting menu [DISPLAY Flashes once every second SETUP] screen is set to [OFF].) Flashes 9 P2 card nearly The remaining P2 card capacity once every full indicator flashes. second during recording. Warning lamp Flashes four times every second Flashes four times every second illuminated Description of the warning and recording/playback behavior Action to take Error in the P2 microcomputer or control. The current operation will stop. Check the factor display*1 and consult the place of purchase. An error occurred in the built-in memory because the P2 card being accessed was ejected. Both of the access LEDs flash in orange. Turn off the power. If the clip in the ejected P2 card contains errors, fix the errors. The battery has run out. Recording and playback will stop. If the voltage drops further, the power is automatically turned off. Change the batteries. Lights up after the recording finishes The P2 card space is used up. Recording will stop.*3 Delete some clips or insert a new card. Flashes four times every second Flashes four times every second Flashes four times every second Error in recording. The recording may stop or continue.*4 Correct recording is not possible due to corruption of the input signal, and the recording is suspended temporarily. The clip will be divided. ffRecording resumes when the signal returns to normal. However, recording does not resume in interval recording, one-shot recording, and loop recording. The error indicates poor wireless audio reception condition. Recording continues without receiving the wireless microphone signal. Turn off the power and on again, and then check your recording and playback. If the recording operation fails, change the P2 card. Check the signal. Check the microphone power supply and the reception status of the wireless receiver. Flashes once every second The battery is about to run out. The current operation will continue.*5 Change the batteries as needed. Flashes once every second during recording. The remaining P2 card capacity is two minutes or less (the remaining indicator display is less than one minute). This warning is issued only during recording. Change the P2 cards as needed or insert an additional card. *1 [P2 SYSTEM ERROR] factor display ff[P2 MICON ERROR]: P2 microcomputer is not responding. ff[P2 CONTROL ERROR]: Error occurred in the P2 recording control. ff[CAM MICON ERROR]: Camera microcomputer is not responding. *2 [REC WARNING] factor display ff[CARD ERROR*]: Error in P2 card (the slot number of the error card is displayed on *). Recording will stop. ff[REC RAM OVERFLOW]: Recording RAM overflow. Recording will stop. ff[PULL DOWN ERROR]: Image pull-down error in 24P, 25P, and 30P. Recording continues. ff[OVER MAX NUMBER CLIPS]: An attempt was made to record more than the maximum number of clips (1000) to one P2 card. ff[ERROR]: Other recording errors. *3 The warning stops if the following operations are made. ffPress the playback related buttons. ffPress the button. ffEject the P2 card or insert another card. *4 The warning stops if the following operations are made. ffPress the button. - 157 -