Panasonic AG-HPX600PJ Operating Instructions - Page 78
Checking and displaying shooting status
View all Panasonic AG-HPX600PJ manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 78 highlights
[REC WARNING] [RUN DOWN CARD] [SYSTEM ERROR] [TEMPORARY PAUSE] [TURN POWER OFF] [VFR ON] [WIRELESS RF] Chapter 4 Adjustments and Settings for Recording - Viewfinder status display An abnormality occurred during recording. Start the recording again. If the warning display persists, contact the shop of purchase. [CARD ERR (1)], [CARD ERR (2)], [CARD ERR (1/2)] P2 card error in slot of indicated number ffIf the warning continues to be displayed, turn off the power. ffIf the warning display persists after retrying recording, replace with another card. [ERROR] Other [OVER MAX# CLIPS] An attempt was made to record more than the maximum number of clips (1000) that can be recorded to a single P2 card. [PULL DOWN ERROR] Abnormality in video pull-down sequence in 24P mode, for example [REC RAM OVERFLOW] Overflow of memory for recording The number of rewrites stipulated for the P2 card has been exceeded. Operation is continued, however, recording or playback might not be performed correctly. Replacement of the P2 card is recommended. This is displayed when an abnormality has occurred on the system. Turn off the power then back on again. [CAM MICON ERROR] No response from camera microcontroller [P2 CONTROL ERROR] P2 control error [P2 MICON ERROR] No response from P2 microcontroller [IRREGULAR FRM SIG] Displayed when the reference signal for generator lock input is disrupted and recording is suspended. An abnormality occurred due to a card being removed while it was being accessed or the system mode was changed. Switch the power off and back on again. [NO AUDIO RECORDING] Displayed when audio signals are not recorded because the VFR mode is set. Wireless receiver reception is poor. Camera system status display [ABB ACTIVE] [ATW ACTIVE] [ATW]/[ATW LOCK] [AUTO KNEE ON]/[OFF] [AWB * ch ACTIVE] [AWB P3.2K]/[AWB P5.6K]/ [AWB VAR*.*K] [BACK LIGHT]/[OFF] [DRS ON]/[OFF] [D.ZOOM **] [GAIN**dB] [ND NG] [SCENE******] [SHUTTER 1/****]/[OFF] [SPOT LIGHT]/[OFF] [FBC ON]/[OFF] Automatic black balance operation display Displayed when the switch is set to the side while the auto tracking white balance function is activated. Displayed when the auto tracking white balance function is assigned, if the switch is set to . Displayed when the selector switch setting was changed. Automatic white balance operation display Displays the assigned color temperature when the switch is set at the position. Also, displayed when an attempt is made to execute the automatic white balance at the position. Displayed when the buttons to which the backlight for iris control is assigned are pressed and the status is switched. Indicates that the dynamic range stretcher operation is switched. Displayed when the button where digital zoom function is assigned or the button on the lens is pressed to switch the status. (×2, ×4, or [OFF] is displayed in the place of **.) Displayed when the gain value is switched. Displayed when the ND filter is not at the correct position. Displays the scene file name when the scene file number is changed to switch the scene file. Displayed when the shutter speed setting was switched. Displayed when the buttons to which the spot light for iris control is assigned are pressed and the status is switched. Indicates that the flash band compensation operation is switched. Checking and displaying shooting status switch ffWhen the switch is pushed from the side towards the side during recording standby or during recording, all information such as the setting status of the shooting functions, functions assigned to the buttons (//) is displayed. Releasing the switch returns the display to the normal display after approximately three seconds. ffWhen the switch is pushed towards the side during recording standby or during recording, most of the displays are turned off. Set it back to , the normal display returns. - 78 -