Home » Lexmark Manuals » Laser Printers » Lexmark Optra C710 » Manual Viewer

Lexmark Optra C710 User's Guide - Page 58

Technical Reference., PCL Emul Menu

Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

PCL Emul Menu The PCL Emul Menu changes printer settings that affect jobs printed using the PCL emulation printer language. For information about the PCL emulation commands supported by your printer, refer to the Technical Reference. PCL Emul Menu Menu item Font Source Values Resident* Download Flash Disk All Font Name This printer setting allows you to select the source which contains the default font selection. The value list only consists of font sources which exist on the printer. In other words, if no download fonts exist in the printer's memory and no flash or disk is installed, then Resident is the only valid value for the Font Source. Note: If a flash or disk device is installed but it is read/write protected, then it is also not a valid selection. Note: Saving Font Source, Font Name, Point Size, Pitch, or Symbol Set has the affect of saving the selected font as the default. Font position and font name for all fonts in the selected font source (R0 Courier 10*) Point Size Always select the font source before you select a font name. After you select a font source, choose the specific font from the Font Name menu item. The printer displays the font source abbreviation, font ID, and font name for each font. The font source abbreviation is R for resident, F for flash, K for disk, and D for download. To print a font sample list showing all the fonts available for PCL emulation, select Print Fonts and then PCL Fonts from the Utilities Menu. Note: Saving Font Source, Font Name, Point Size, Pitch, or Symbol Set will save the selected font as the default. 1...1008 (in increments of 0.25) (12*) *Factory default If you chose a scalable typographic font, you can select the point size for the font. Point size refers to the height of the characters in the font. One point equals approximately 1/72 of an inch. You can select point sizes from 1 to 1008 in increments of 0.25 points. Note: Saving Font Source, Font Name, Point Size, Pitch, or Symbol Set will save the selected font as the default. 44 Chapter 3: Menus

Section	Page
Table of contents	3
Using your documentation ix	3
Trademarks xiii	3
1 Introducing your printer 1	3
2 Using printer drivers 5	3
3 Changing printer settings 7	3
4 Using color 75	4
5 Managing memory 89	5
6 Handling paper 95	5
7 Replacing supplies 113	6
8 Solving printer problems 145	6
Appendix A: MarkVision 189	7
Appendix B: Printer specifications 201	7
Appendix C: Fonts 205	7
Appendix D: Safety information 215	7
Appendix E: Notices 227	7
Appendix F: Warranty 239	8
Glossary 241	8
Index 255	8
Using your documentation	9
About the manuals	9
Other sources ofinformation	11
Trademarks	13
Introducing your printer	15
Print speed	16
Memory	16
Color quality	16
Printer drivers	17
MarkVision	17
Paper handling	17
Using printer drivers	19
Changing printer settings	21
Using the operator panel	22
Menus	24
Using color	89
Understanding color	89
Managing color	92
Controlling your printer	94
Color Correction	98
Avoiding print quality problems	100
Managing memory	103
Printer memory	103
Adding memory	104
Flash memory	106
Hard disk	106
Managing resources downloaded to flash or disk	107
Handling paper	109
Paper sources and output bins	109
Paper sizes	110
Media guidelines	112
Storing media	118
Avoiding paperjams	118
Loading paper inthe trays	119
Tray linking	123
Using the multipurpose feeder	124
Replacing supplies	127
Ordering supplies	127
Storing supplies	129
When to replacesupplies	130
Recycling usedsupplies	133
Conserving supplies	133
Replacing supplyitems	134
Replacing print cartridges	135
Replacing the coating roll	140
Replacing the fuser kit	145
Replacing the transfer kit	152
Solving printer problems	159
Printer problems	159
Theory of operation	160
Understanding printer messages	161
Identifying other problems	175
Clearing printer paperjams	182
Clearing duplex unit paperjams	189
Cleaning the print cartridge dust collector	195
Cleaning the waste toner sensor	198
Calling for customer support	202
MarkVision	203
Operating systems supported	203
Introducing MarkVision	204
Installing MarkVision on a network	212
Getting updated utilities and drivers	213
Printer specifications	215
Fonts	219
Printing font samples	219
Resident fonts	220
Symbol Sets	225
Downloadable fonts	227
Safety information	229
Notices	241
Laser notices	245
Warranty	253
Glossary	255
A	255
B	256
C	256
D	257
E	258
F	259
G	259
H	260
I	260
J	260
K	260
L	261
M	261
N	262
O	262
P	263
R	265
S	265
T	267
U	267
V	267
Y	268

Match case Limit results 1 per page

Chapter 3: Menus

PCL Emul Menu

The PCL Emul Menu changes printer settings that affect jobs

printed using the PCL emulation printer language. For informa-

tion about the PCL emulation commands supported by your

printer, refer to the

Technical Reference.

PCL Emul Menu

Menu item

Values

Font Source

Resident*

Download

Flash

Disk

All

This printer setting allows you to select the source which contains the default font selection.

The value list only consists of font sources which exist on the printer. In other words, if no

download fonts exist in the printer’s memory and no flash or disk is installed, then Resident is

the only valid value for the Font Source.

Note:

If a flash or disk device is installed but it is read/write protected, then it is also not a valid

selection.

Note:

Saving Font Source, Font Name, Point Size, Pitch, or Symbol Set has the affect of

saving the selected font as the default.

Font Name

Font position and font name for all fonts in the selected font source

(R0 Courier 10*)

Always select the font source before you select a font name. After you select a font source,

choose the specific font from the Font Name menu item. The printer displays the font source

abbreviation, font ID, and font name for each font. The font source abbreviation is R for

resident, F for flash, K for disk, and D for download.

To print a font sample list showing all the fonts available for PCL emulation, select Print Fonts

and then PCL Fonts from the Utilities Menu.

Note:

Saving Font Source, Font Name, Point Size, Pitch, or Symbol Set will save the selected

font as the default.

Point Size

1…1008 (in increments of 0.25)

(12*)

If you chose a scalable typographic font, you can select the point size for the font. Point size

refers to the height of the characters in the font. One point equals approximately 1/72 of an

inch. You can select point sizes from 1 to 1008 in increments of 0.25 points.

Note:

Saving Font Source, Font Name, Point Size, Pitch, or Symbol Set will save the selected

font as the default.

*Factory default