HP Integrity rx2800 HP Insight Management WBEM Provider Events Reference Guide - Page 12
power source. WBEM EventID: 139. WBEM ProviderName: SEL02_IndicationProvider.
View all HP Integrity rx2800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
710 Warning Fan speed lags. Probable Cause: Possibly, the specified fan is beginning to lose performance. Recommended Action: If these errors continue to be reported, the fan should be replaced. WBEM EventID: 126. WBEM ProviderName: SEL02_IndicationProvider. 720 Warning Power supply failure. Probable Cause: The system has detected that one of the power supplies has failed. Recommended Action: The power cable has been disconnected. Reconnect, or The power supply has failed. Contact your HP support representative to check the power supply. WBEM EventID: 137. WBEM ProviderName: SEL02_IndicationProvider. 720 Warning Power supply failure. Probable Cause: The system has detected that one of the power supplies has failed. Recommended Action: The power cable has been disconnected. Reconnect, or The power supply has failed. Contact your HP support representative to check the power supply. WBEM EventID: 137. WBEM ProviderName: SEL02_IndicationProvider. 722 Warning Power supply AC lost. Probable Cause: The power supply has lost its A/C source. The power supply is not connected to a working A/C power source. Recommended Action: Verify that the plug is connected to the power supply, and to a working power source. WBEM EventID: 139. WBEM ProviderName: SEL02_IndicationProvider. 722 Warning Power supply AC lost. Probable Cause: The power supply has lost its A/C source. The power supply is not connected to a working A/C power source. Recommended Action: Verify that the plug is connected to the power supply, and to a working power source. WBEM EventID: 139. WBEM ProviderName: SEL02_IndicationProvider. 726 Error Power failure in power supply. Probable Cause: Indicates a failure with the AC power source that is connected to one of the redundant power supply units. Recommended Action: Check the power cord or source voltage. WBEM EventID: 155. WBEM ProviderName: SEL02_IndicationProvider. 726 Error Power failure in power supply. Probable Cause: Indicates a failure with the AC power source that is connected to one of the redundant power supply units. Recommended Action: Check the power cord or source voltage. WBEM EventID: 155. WBEM ProviderName: SEL02_IndicationProvider. 728 Error Voltage reached critical level. Probable Cause: The voltage in the server has gone outside the factory set range. A bad component, blown fuse, poorly seated module, loose cable, or debris could be responsible for this failure. Recommended Action: Check all boards, power supplies, and modules that either supply or use this voltage rail. WBEM EventID: 119. WBEM ProviderName: SEL02_IndicationProvider. 728 Error Voltage reached critical level. Probable Cause: The voltage in the server has gone outside the factory set range. A bad component, blown fuse, poorly seated module, loose cable, or debris could be responsible for this failure. Recommended Action: Check all boards, power supplies, and modules that either supply or use this voltage rail. WBEM EventID: 119. WBEM ProviderName: SEL02_IndicationProvider. 729 Error System shut-down or reset caused by sensor reading. Probable Cause: A sensor reading in the system was determined to be non-recoverable and the system was shut down or reset. Recommended Action: Read the system logs to find which sensor was out of range. WBEM EventID: 167. WBEM ProviderName: SEL02_IndicationProvider. 729 Error System shut-down or reset caused by sensor reading. Probable Cause: A sensor reading in the system was determined to be non-recoverable and the system was shut down or reset. Recommended Action: Read the system logs to find which sensor was out of range. WBEM EventID: 167. WBEM ProviderName: SEL02_IndicationProvider. 12 WBEM Provider Event Tables