HP Integrity rx2800 HP Insight Management WBEM Provider Events Reference Guide - Page 51

7953 7963 7964 7965 7966 7973 7974 7975 8009 8010 8127 8128 8130 8131 Error Error Error Error Error Error Error Error Error Warning Error Error Warning Warning CPUs loaded in wrong order. Probable Cause: CPUs not loaded in correct order. Recommended Action: Load CPUs in order 0, 1, 2, 3. WBEM EventID: 615. WBEM ProviderName: FPL_IndicationProvider. The XBC SBE and LPE errors were not cleared properly. Probable Cause: the link generated a new error. Recommended Action: check CC, check link Check logs for other errors. If error is persistent, replace cell board. WBEM EventID: 1031. WBEM ProviderName: FPL_IndicationProvider. The CC to XBC link pattern test failed. Probable Cause: Unspecified. WBEM EventID: 2438. WBEM ProviderName: FPL_IndicationProvider. Error Reading a platform storage variable from the PDHC/MP. Probable Cause: Either the MP is not present, or the requested information does not exist. Ensure that the MP is functioning and that the proper data is being requested. WBEM EventID: 616. WBEM ProviderName: FPL_IndicationProvider. An error was returned on a Platform Storage Write Command to the PDHC/MP. Probable Cause: The MP is not present, may be out of space, or the command was badly formatted. Ensure that the MP has enough space and try again. If the problem persists, contact engineering. WBEM EventID: 617. WBEM ProviderName: FPL_IndicationProvider. The Sequencer was unable to find/use a needed tree node. Probable Cause: This is a bug, contact engineering. WBEM EventID: 618. WBEM ProviderName: FPL_IndicationProvider. Firmware encountered an error in processing the partition variables. Probable Cause: Either the GSP was not present or there was a resource problem storing the variable. There should be other clues in the event id log to indicate which is the case. Restore the GSP. WBEM EventID: 619. WBEM ProviderName: FPL_IndicationProvider. A non-critical cell power fault has occurred. Probable Cause: A CPU Power Module has been disabled following a thermal warning reported by that CPU Module. Recommended Action: Contact HP Support personnel to troubleshoot the problem. WBEM EventID: 620. WBEM ProviderName: FPL_IndicationProvider. CPUProcConfigValue in /options is not compatible with the current PAL/CPU. Probable Cause: Modify CPUProcConfigValue in /options to set the correct bits. WBEM EventID: 2439. WBEM ProviderName: FPL_IndicationProvider. Firmware was unable to determine the Processor Dependent Features. Probable Cause: Contact Engineering, This is a bug. WBEM EventID: 622. WBEM ProviderName: FPL_IndicationProvider. Data field contains data meant for firmware debug only. Probable Cause: Debug event. Recommended Action: Contact your hp support representative. WBEM EventID: 2434. WBEM ProviderName: FPL_IndicationProvider. The CLU has encountered an undefined case. Probable Cause: CLU firmware on the UGUY has gotten into an unexpected execution path, most likely due to a hardware issue on the UGUY. Recommended Action: Check revision of CLU firmware. If out of date, or known bad revision, use FWUU to update CLU firmware. Contact HP Support personnel to troubleshoot problem. WBEM EventID: 624. WBEM ProviderName: FPL_IndicationProvider. An unknown Cell voltage margin has been detected. Probable Cause: A user has manually, using back-door debugging methods, altered the voltage margin setting of one or more Cell Board or Cell Power Board converters. WBEM EventID: 625. WBEM ProviderName: FPL_IndicationProvider. The run-time verification of a programming assumption has failed. Probable Cause: Hardware or software in unknown state. Recommended Action: Upgrade PDHC firmware to latest revision. If already at current revision, contact HP Support personnel to troubleshoot the problem. WBEM EventID: 626. WBEM ProviderName: FPL_IndicationProvider. Platform Events 51