HP Integrity rx2800 HP Insight Management WBEM Provider Events Reference Guide - Page 9
Hot Swap Cage: SCSI cable removed. Probable Cause: This alert indicates that a SCSI
View all HP Integrity rx2800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
9 Error Voltage sensor crossed lower non-recoverable threshold. Probable Cause: The voltage in the server has gone far outside the factory set range and could damage system components. A bad component, blown fuse, poorly seated module, loose cable, or debris could be responsible for this failure. Recommended Action: Check all boards, power supplies, and modules that either supply or use this voltage rail. WBEM EventID: 114. WBEM ProviderName: SEL02_IndicationProvider. 10 Warning A measured voltage in the server has gone outside the factory specified upper voltage range. Probable Cause: The voltage in the server has gone outside the factory set range. A bad component, blown fuse, poorly seated module, loose cable, or debris could be responsible for this failure. Recommended Action: Check all boards, power supplies, and modules that either supply or use this voltage rail. WBEM EventID: 115. WBEM ProviderName: SEL02_IndicationProvider. 10 Warning A measured voltage in the server has gone outside the factory specified upper voltage range. Probable Cause: The voltage in the server has gone outside the factory set range. A bad component, blown fuse, poorly seated module, loose cable, or debris could be responsible for this failure. Recommended Action: Check all boards, power supplies, and modules that either supply or use this voltage rail. WBEM EventID: 115. WBEM ProviderName: SEL02_IndicationProvider. 12 Error Voltage sensor crossed upper non-recoverable threshold. Probable Cause: The voltage in the server has gone far outside the factory set range and could damage system components. A bad component, blown fuse, poorly seated module, loose cable, or debris could be responsible for this failure. Recommended Action: Check all boards, power supplies, and modules that either supply or use this voltage rail. WBEM EventID: 116. WBEM ProviderName: SEL02_IndicationProvider. 12 Error Voltage sensor crossed upper non-recoverable threshold. Probable Cause: The voltage in the server has gone far outside the factory set range and could damage system components. A bad component, blown fuse, poorly seated module, loose cable, or debris could be responsible for this failure. Recommended Action: Check all boards, power supplies, and modules that either supply or use this voltage rail. WBEM EventID: 116. WBEM ProviderName: SEL02_IndicationProvider. 26 Warning The server's built-in sensors have detected an open chassis door. Probable Cause: The server has detect that the chassis door or other access panel is not securely closed. Recommended Action: Close any open panels or chassis doors. WBEM EventID: 127. WBEM ProviderName: SEL02_IndicationProvider. 26 Warning The server's built-in sensors have detected an open chassis door. Probable Cause: The server has detect that the chassis door or other access panel is not securely closed. Recommended Action: Close any open panels or chassis doors. WBEM EventID: 127. WBEM ProviderName: SEL02_IndicationProvider. 62 Warning Power supply subsystem redundancy lost. Probable Cause: The Power Supply Subsystem now has only the minimum number of working power supply units required to maintain normal operation. There is no redundant (backup) power supply unit if one fails. Recommended Action: Since your server still has the minimum number of operational power supply modules, no immediate action is required. However, you should inspect the server for any bad power supply modules and replace them as soon as possible. WBEM EventID: 153. WBEM ProviderName: SEL02_IndicationProvider. 62 Warning Power supply subsystem redundancy lost. Probable Cause: The Power Supply Subsystem now has only the minimum number of working power supply units required to maintain normal operation. There is no redundant (backup) power supply unit if one fails. Recommended Action: Since your server still has the minimum number of operational power supply modules, no immediate action is required. However, you should inspect the server for any bad power supply modules and replace them as soon as possible. WBEM EventID: 153. WBEM ProviderName: SEL02_IndicationProvider. 113 Warning Hot Swap Cage: SCSI cable removed. Probable Cause: This alert indicates that a SCSI cable, Jumper or Duplex Connector has either been disconnected or removed. This may make some SCSI devices inaccessible. Recommended Action: Ensure that all the required SCSI cables, jumpers or duplex connectors are correctly connected to the cage, disks, and/or the controller. WBEM EventID: 174. WBEM ProviderName: SEL02_IndicationProvider. Platform Events 9