HP Integrity rx2800 HP Insight Management WBEM Provider Events Reference Guide - Page 55

either the PCI card or the I/O backplane. WBEM EventID: 788. WBEM ProviderName

Get HP Integrity rx2800 - i2 PDF manuals and user guides View all HP Integrity rx2800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

8710 8711 8712 8713 8714 8715 8716 8717 8718 8719 8720 8721 8722 8723 8747 Error Error Warning Warning Error Warning Error Warning Warning Error Error Warning Error Error Error There was an error discovering the SBA. Probable Cause: An error was discovered with the SBA during discovery. Recommended Action: Correct any previous errors Replace the I/O backplane. WBEM EventID: 780. WBEM ProviderName: FPL_IndicationProvider. An error was encountered while resetting the SBA. Probable Cause: The SBA component could not reset one or more LBA ropes, probably due to faulty hardware. Recommended Action: Replace the failed IO backplane. WBEM EventID: 781. WBEM ProviderName: FPL_IndicationProvider. There was an error initializing the IO link. Probable Cause: The SBA IO link could not be initialized, probably due to cable installation errors or faulty hardware. Recommended Action: Re-install or replace the cables; replace the IO backplane. WBEM EventID: 782. WBEM ProviderName: FPL_IndicationProvider. There is a problem initializing the REO cable. Probable Cause: An SBA IO cable error has been detected. Recommended Action: Verify proper cable connection, repair/replace the cables. WBEM EventID: 783. WBEM ProviderName: FPL_IndicationProvider. The IO chassis discovered was powered off. Probable Cause: Connected IO chassis is powered off. Recommended Action: Either power on the IO chassis or ignore the error if it is powered off by design. WBEM EventID: 784. WBEM ProviderName: FPL_IndicationProvider. There was an error initializing the LBA. Probable Cause: The LBA component initialization routine failed. Recommended Action: This is an internal system firmware error. Update system firmware or contact a system firmware representative. WBEM EventID: 785. WBEM ProviderName: FPL_IndicationProvider. There was an error querying the LBA width. Probable Cause: Error while writing the LBA phase data. Recommended Action: Replace the I/O backplane. WBEM EventID: 786. WBEM ProviderName: FPL_IndicationProvider. There was an error with the LBA phase. Probable Cause: Error while writing the LBA phase data. Recommended Action: Replace the I/O backplane. WBEM EventID: 787. WBEM ProviderName: FPL_IndicationProvider. There was an error clearing the LBA. Probable Cause: Unable to clear an error in the LBA. Recommended Action: Check other events for the error being generated replace either the PCI card or the I/O backplane. WBEM EventID: 788. WBEM ProviderName: FPL_IndicationProvider. There was an error with the LBA log. Probable Cause: The LBA component could not generate error logs. Recommended Action: This is an internal system firmware error. Update system firmware or contact a system firmware representative. WBEM EventID: 789. WBEM ProviderName: FPL_IndicationProvider. There was an error discovering the LBA. Probable Cause: The wrong backplane type was detected. Recommended Action: replace I/O backplane. WBEM EventID: 790. WBEM ProviderName: FPL_IndicationProvider. There was an error configuring the LBA. Probable Cause: Unable to configure the LBA. Recommended Action: replace I/O backplane. WBEM EventID: 791. WBEM ProviderName: FPL_IndicationProvider. There was an error scanning the PCI bus. Probable Cause: Could not scan the card in a populated slot. Typically caused by an improperly installed or faulty PCI card. Recommended Action: Reseat or replace the faulty card. WBEM EventID: 792. WBEM ProviderName: FPL_IndicationProvider. There was an error configuring PCI space through the LBA. Probable Cause: Unable to obtain semaphore. Recommended Action: reset Update to latest recipe. WBEM EventID: 793. WBEM ProviderName: FPL_IndicationProvider. Firmware was unable to find a suitable block of main memory to relocate ROM. Probable Cause: Probably caused by lots of PDT entries, or no main memory present. WBEM EventID: 1036. WBEM ProviderName: FPL_IndicationProvider. Platform Events 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
There was an error discovering the SBA. Probable Cause: An error was discovered
with the SBA during discovery. Recommended Action: Correct any previous errors
Replace the I/O backplane. WBEM EventID: 780. WBEM ProviderName:
FPL_IndicationProvider.
Error
8710
An error was encountered while resetting the SBA. Probable Cause: The SBA
component could not reset one or more LBA ropes, probably due to faulty hardware.
Recommended Action: Replace the failed IO backplane. WBEM EventID: 781. WBEM
ProviderName: FPL_IndicationProvider.
Error
8711
There was an error initializing the IO link. Probable Cause: The SBA IO link could
not be initialized, probably due to cable installation errors or faulty hardware.
Recommended Action: Re-install or replace the cables; replace the IO backplane.
WBEM EventID: 782. WBEM ProviderName: FPL_IndicationProvider.
Warning
8712
There is a problem initializing the REO cable. Probable Cause: An SBA IO cable error
has been detected. Recommended Action: Verify proper cable connection,
repair/replace the cables. WBEM EventID: 783. WBEM ProviderName:
FPL_IndicationProvider.
Warning
8713
The IO chassis discovered was powered off. Probable Cause: Connected IO chassis
is powered off. Recommended Action: Either power on the IO chassis or ignore the
error if it is powered off by design. WBEM EventID: 784. WBEM ProviderName:
FPL_IndicationProvider.
Error
8714
There was an error initializing the LBA. Probable Cause: The LBA component
initialization routine failed. Recommended Action: This is an internal system firmware
error. Update system firmware or contact a system firmware representative. WBEM
EventID: 785. WBEM ProviderName: FPL_IndicationProvider.
Warning
8715
There was an error querying the LBA width. Probable Cause: Error while writing
the LBA phase data. Recommended Action: Replace the I/O backplane. WBEM
EventID: 786. WBEM ProviderName: FPL_IndicationProvider.
Error
8716
There was an error with the LBA phase. Probable Cause: Error while writing the LBA
phase data. Recommended Action: Replace the I/O backplane. WBEM EventID: 787.
WBEM ProviderName: FPL_IndicationProvider.
Warning
8717
There was an error clearing the LBA. Probable Cause: Unable to clear an error in the
LBA. Recommended Action: Check other events for the error being generated replace
either the PCI card or the I/O backplane. WBEM EventID: 788. WBEM ProviderName:
FPL_IndicationProvider.
Warning
8718
There was an error with the LBA log. Probable Cause: The LBA component could
not generate error logs. Recommended Action: This is an internal system firmware
error. Update system firmware or contact a system firmware representative. WBEM
EventID: 789. WBEM ProviderName: FPL_IndicationProvider.
Error
8719
There was an error discovering the LBA. Probable Cause: The wrong backplane type
was detected. Recommended Action: replace I/O backplane. WBEM EventID: 790.
WBEM ProviderName: FPL_IndicationProvider.
Error
8720
There was an error configuring the LBA. Probable Cause: Unable to configure the
LBA. Recommended Action: replace I/O backplane. WBEM EventID: 791. WBEM
ProviderName: FPL_IndicationProvider.
Warning
8721
There was an error scanning the PCI bus. Probable Cause: Could not scan the card
in a populated slot. Typically caused by an improperly installed or faulty PCI card.
Recommended Action: Reseat or replace the faulty card. WBEM EventID: 792. WBEM
ProviderName: FPL_IndicationProvider.
Error
8722
There was an error configuring PCI space through the LBA. Probable Cause: Unable
to obtain semaphore. Recommended Action: reset Update to latest recipe. WBEM
EventID: 793. WBEM ProviderName: FPL_IndicationProvider.
Error
8723
Firmware was unable to find a suitable block of main memory to relocate ROM.
Probable Cause: Probably caused by lots of PDT entries, or no main memory present.
WBEM EventID: 1036. WBEM ProviderName: FPL_IndicationProvider.
Error
8747
Platform Events
55