HP Integrity rx2800 HP Insight Management WBEM Provider Events Reference Guide - Page 61

system, and then initiate O/S boot. WBEM EventID: 985. WBEM ProviderName

Get HP Integrity rx2800 - i2 PDF manuals and user guides View all HP Integrity rx2800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

9653 9658 9678 9681 9682 9685 9740 9741 9744 9745 9746 9750 Warning Error Error Error Warning Error Error Error Error Error Error Warning Windows: Server Agents Management data not accessible, locked property. Probable Cause: The installed management software has detected an unstable state of the underlying IPMI (Intelligent Platform Management Interface) subsystem and has disabled all management information from being shown by any manageability applications. The management information will become available automatically as soon as the IPMI subsystem has stabilized. Recommended Action: No action is required. WBEM EventID: 1806. WBEM ProviderName: FPL_IndicationProvider. PCI slot exceeds power limit. Probable Cause: The I/O configuration's power consumption exceeds the supported limit. Recommended Action: Remove the I/O card from each slot indicated by an IO_PCI_POWER_OVERLOAD_ERR event. WBEM EventID: 976. WBEM ProviderName: FPL_IndicationProvider. The clock ratio reported by manageability does not match the actual clock ratio. Probable Cause: This is a hardware error and it is fatal. WBEM EventID: 2687. WBEM ProviderName: FPL_IndicationProvider. Manual override of fatal stop boot condition. Probable Cause: The user has initiated manual O/S boot despite the existence of a error. Recommended Action: Correct the error condition (see output of 'INFO WARNING' EFI shell command), reboot the system, and then initiate O/S boot. WBEM EventID: 985. WBEM ProviderName: FPL_IndicationProvider. Firmware unable to relocate VGA BIOS. Probable Cause: Most likely there is a permanent memory error in the VGA BIOS region (physical address 0xc0000 - 0xdffff). Recommended Action: Replace the DIMM causing the permanent memory error in the VGA BIOS region. The PDT reports which DIMM is causing errors in the physical address range 0xc0000 - 0xdffff. WBEM EventID: 986. WBEM ProviderName: FPL_IndicationProvider. The Compatibility Matrix stored in NVRAM has a checksum error. Probable Cause: NVRAM has become corrupt. Restore from a backup. WBEM EventID: 987. WBEM ProviderName: FPL_IndicationProvider. The buffer size is too small for the XBC error log. Probable Cause: Firmware error. Recommended Action: Reset cell. WBEM EventID: 1002. WBEM ProviderName: FPL_IndicationProvider. System firmware was unable to clear an XBC error. Probable Cause: The particular XBC and port could have a persistent error. Recommended Action: Check flex cable indicated by event data. WBEM EventID: 1003. WBEM ProviderName: FPL_IndicationProvider. Error encountered while collecting PCI error logs. Probable Cause: An error occurred while collecting the PCI error logs. Recommended Action: No action can be taken. The result is some or all PCI error logs will be unavailable. WBEM EventID: 2446. WBEM ProviderName: FPL_IndicationProvider. Error encountered while collecting SBA error logs. Probable Cause: An error occurred while collecting the SBA error logs. Recommended Action: No action can be taken. The result is some or all SBA error logs will be unavailable. WBEM EventID: 2447. WBEM ProviderName: FPL_IndicationProvider. Fabric is unable to route the crossbar after multiple retry attempts. Probable Cause: Hardware problem. Possible bad XBC or Cell Controller. Recommended Action: Check for hardware failures. Reset backplane to re-initialize fabric. WBEM EventID: 1005. WBEM ProviderName: FPL_IndicationProvider. Windows: Predictive Failure in Memory (Warning). Probable Cause: You will receive this message if the system is correcting a lot of ECC single bit errors. It may mean that the module is about to fail, or environmental conditions in the server are causing more errors than usual. This event message will be generated for one of the following conditions 1000 single-bit errors on the same address in a 48 hour time period. 50 single-bit errors on the same DIMM (not the same address) in a 24 hour time period. 100 single-bit errors on the same DIMM (not the same address) in a 1 week time period. Recommended Action: If you receive this message, contact your support provider to determine if a predictive repair should be made. WBEM EventID: 1820. WBEM ProviderName: FPL_IndicationProvider. Platform Events 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Windows: Server Agents Management data not accessible, locked property. Probable
Cause: The installed management software has detected an unstable state of the
underlying IPMI (Intelligent Platform Management Interface) subsystem and has
disabled all management information from being shown by any manageability
applications. The management information will become available automatically as
soon as the IPMI subsystem has stabilized. Recommended Action: No action is
required. WBEM EventID: 1806. WBEM ProviderName: FPL_IndicationProvider.
Warning
9653
PCI slot exceeds power limit. Probable Cause: The I/O configuration's power
consumption exceeds the supported limit. Recommended Action: Remove the I/O
card from each slot indicated by an IO_PCI_POWER_OVERLOAD_ERR event. WBEM
EventID: 976. WBEM ProviderName: FPL_IndicationProvider.
Error
9658
The clock ratio reported by manageability does not match the actual clock ratio.
Probable Cause: This is a hardware error and it is fatal. WBEM EventID: 2687. WBEM
ProviderName: FPL_IndicationProvider.
Error
9678
Manual override of fatal stop boot condition. Probable Cause: The user has initiated
manual O/S boot despite the existence of a error. Recommended Action: Correct the
error condition (see output of 'INFO WARNING' EFI shell command), reboot the
system, and then initiate O/S boot. WBEM EventID: 985. WBEM ProviderName:
FPL_IndicationProvider.
Error
9681
Firmware unable to relocate VGA BIOS. Probable Cause: Most likely there is a
permanent memory error in the VGA BIOS region (physical address 0xc0000 - 0xdffff).
Recommended Action: Replace the DIMM causing the permanent memory error in
the VGA BIOS region. The PDT reports which DIMM is causing errors in the physical
address range 0xc0000 - 0xdffff. WBEM EventID: 986. WBEM ProviderName:
FPL_IndicationProvider.
Warning
9682
The Compatibility Matrix stored in NVRAM has a checksum error. Probable Cause:
NVRAM has become corrupt. Restore from a backup. WBEM EventID: 987. WBEM
ProviderName: FPL_IndicationProvider.
Error
9685
The buffer size is too small for the XBC error log. Probable Cause: Firmware error.
Recommended Action: Reset cell. WBEM EventID: 1002. WBEM ProviderName:
FPL_IndicationProvider.
Error
9740
System firmware was unable to clear an XBC error. Probable Cause: The particular
XBC and port could have a persistent error. Recommended Action: Check flex cable
indicated by event data. WBEM EventID: 1003. WBEM ProviderName:
FPL_IndicationProvider.
Error
9741
Error encountered while collecting PCI error logs. Probable Cause: An error occurred
while collecting the PCI error logs. Recommended Action: No action can be taken.
The result is some or all PCI error logs will be unavailable. WBEM EventID: 2446.
WBEM ProviderName: FPL_IndicationProvider.
Error
9744
Error encountered while collecting SBA error logs. Probable Cause: An error occurred
while collecting the SBA error logs. Recommended Action: No action can be taken.
The result is some or all SBA error logs will be unavailable. WBEM EventID: 2447.
WBEM ProviderName: FPL_IndicationProvider.
Error
9745
Fabric is unable to route the crossbar after multiple retry attempts. Probable Cause:
Hardware problem. Possible bad XBC or Cell Controller. Recommended Action:
Check for hardware failures. Reset backplane to re-initialize fabric. WBEM EventID:
1005. WBEM ProviderName: FPL_IndicationProvider.
Error
9746
Windows: Predictive Failure in Memory (Warning). Probable Cause: You will receive
this message if the system is correcting a lot of ECC single bit errors. It may mean
that the module is about to fail, or environmental conditions in the server are causing
more errors than usual. This event message will be generated for one of the following
conditions 1000 single-bit errors on the same address in a 48 hour time period. 50
single-bit errors on the same DIMM (not the same address) in a 24 hour time period.
100 single-bit errors on the same DIMM (not the same address) in a 1 week time
period. Recommended Action: If you receive this message, contact your support
provider to determine if a predictive repair should be made. WBEM EventID: 1820.
WBEM ProviderName: FPL_IndicationProvider.
Warning
9750
Platform Events
61