HP Integrity rx2800 HP Insight Management WBEM Provider Events Reference Guide - Page 90

Recommended Action: Make sure to have HP supported DIMMs installed. WBEM

Get HP Integrity rx2800 - i2 PDF manuals and user guides View all HP Integrity rx2800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

12408 Warning 12411 Warning 12489 Error 12492 Warning 12557 Warning 12560 Error 12586 Error 12589 Error 12591 Error 12593 Error 12595 Error The OA was unable to service a power-on request. Try re-issuing the power-on request. If the problem reoccurs after subsequent requests, notify the Call Center for assistance. Probable Cause: If Onboard Administrator is busy in processing another requests, then it sends BUSY response for any requests that cannot be processed in time. Recommended Action: Try issuing the requests after some time. If the problem exists even after subsequent requests, please contact the HP representative. WBEM EventID: 7013. WBEM ProviderName: FPL_IndicationProvider. The IO backplane in the specified cabinet is reporting a non-redundant PCI power condition. It is possible that one of the PCI bricks is not present or not functioning properly. Check for PCI brick fault events. Probable Cause: One of the PCI bricks is not present or not functioning properly. Recommended Action: Check for PCI brick fault events. WBEM EventID: 7014. WBEM ProviderName: FPL_IndicationProvider. The Root Port initialization detected a PCI express link training failure. Probable Cause: The RP component detected a PCIe link training error, probably due to failed hardware. Recommended Action: Reseat or replace the PCIe card; update system firmware; replace the I/O riser if applicable; replace the motherboard. WBEM EventID: 9886. WBEM ProviderName: FPL_IndicationProvider. The Root Port component had insufficient GMMIO to support the PCIe request. Probable Cause: The RP component had insufficient GMMIO resources to support a board request. Recommended Action: Replace the faulty card; remove one or more PCIe cards to reduce GMMIO requirements. WBEM EventID: 9889. WBEM ProviderName: FPL_IndicationProvider. HP unsupported DIMM(s) has been detected on this partition. Probable Cause: HP PFM service has detected one or more HP unsupported DIMMs on this partition. Recommended Action: Make sure to have HP supported DIMMs installed. WBEM EventID: 7243. WBEM ProviderName: FPL_IndicationProvider. OS run-time critical shutdown occurred. Probable Cause: The OS has caused the system to shut down. Recommended Action: Look at OS logs and crash data to determine why the system shut down. WBEM EventID: 7244. WBEM ProviderName: FPL_IndicationProvider. The amount of power expected to be drawn by the currently operating hardware is greater than the rating of the currently operating Bulk Power Supplies (BPS). Probable Cause: A bulk power supply has failed or was removed when the system had the minimal number of required bulk power supplies. Recommended Action: Replace the failed or removed bulk power supply. WBEM EventID: 7250. WBEM ProviderName: FPL_IndicationProvider. Bulk power supply (BPS) redundancy has been lost on one or more row(s) of power supplies in the complex. The further loss of a single BPS or an AC grid will most likely result in the shutdown of partitions. Probable Cause: An AC source has been lost. Recommended Action: Verify that the chassis is connected to working power grid(s). WBEM EventID: 7253. WBEM ProviderName: FPL_IndicationProvider. AC redundancy has been lost on one or more power supplies in the complex. The further loss of a single Bulk Power Supply (BPS) or the other AC grid will most likely result in the shutdown of partitions. Probable Cause: A change has occurred in the number of properly operating bulk power supplies installed in the system. Recommended Action: Replace missing or failed bulk power supplies. WBEM EventID: 7255. WBEM ProviderName: FPL_IndicationProvider. The fans that cool a region of the system are not redundant. If an additional fan fails or is removed from this cooling domain, the partitions on this system will be shut down to prevent damage. Probable Cause: One or more fans in the cooling domain have been removed or are not functioning properly. Recommended Action: Removed failed fan (if any) and insert working fan. WBEM EventID: 7256. WBEM ProviderName: FPL_IndicationProvider. An insufficient number of fans are working in a cooling domain to permit system operation. Running partitions will be shut down immediately to prevent damage due to excessive heat. Probable Cause: More than one fan in a cooling domain have been removed or are not functioning properly. Recommended Action: Remove failed fan(s), if any, and insert working fans. WBEM EventID: 7258. WBEM ProviderName: FPL_IndicationProvider. 90 WBEM Provider Event Tables

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
The OA was unable to service a power-on request. Try re-issuing the power-on
request. If the problem reoccurs after subsequent requests, notify the Call Center for
assistance. Probable Cause: If Onboard Administrator is busy in processing another
requests, then it sends BUSY response for any requests that cannot be processed in
time. Recommended Action: Try issuing the requests after some time. If the problem
exists even after subsequent requests, please contact the HP representative. WBEM
EventID: 7013. WBEM ProviderName: FPL_IndicationProvider.
Warning
12408
The IO backplane in the specified cabinet is reporting a non-redundant PCI power
condition. It is possible that one of the PCI bricks is not present or not functioning
properly. Check for PCI brick fault events. Probable Cause: One of the PCI bricks is
not present or not functioning properly. Recommended Action: Check for PCI brick
fault events. WBEM EventID: 7014. WBEM ProviderName: FPL_IndicationProvider.
Warning
12411
The Root Port initialization detected a PCI express link training failure. Probable
Cause: The RP component detected a PCIe link training error, probably due to failed
hardware. Recommended Action: Reseat or replace the PCIe card; update system
firmware; replace the I/O riser if applicable; replace the motherboard. WBEM EventID:
9886. WBEM ProviderName: FPL_IndicationProvider.
Error
12489
The Root Port component had insufficient GMMIO to support the PCIe request.
Probable Cause: The RP component had insufficient GMMIO resources to support
a board request. Recommended Action: Replace the faulty card; remove one or more
PCIe cards to reduce GMMIO requirements. WBEM EventID: 9889. WBEM
ProviderName: FPL_IndicationProvider.
Warning
12492
HP unsupported DIMM(s) has been detected on this partition. Probable Cause: HP
PFM service has detected one or more HP unsupported DIMMs on this partition.
Recommended Action: Make sure to have HP supported DIMMs installed. WBEM
EventID: 7243. WBEM ProviderName: FPL_IndicationProvider.
Warning
12557
OS run-time critical shutdown occurred. Probable Cause: The OS has caused the
system to shut down. Recommended Action: Look at OS logs and crash data to
determine why the system shut down. WBEM EventID: 7244. WBEM ProviderName:
FPL_IndicationProvider.
Error
12560
The amount of power expected to be drawn by the currently operating hardware is
greater than the rating of the currently operating Bulk Power Supplies (BPS). Probable
Cause: A bulk power supply has failed or was removed when the system had the
minimal number of required bulk power supplies. Recommended Action: Replace
the failed or removed bulk power supply. WBEM EventID: 7250. WBEM
ProviderName: FPL_IndicationProvider.
Error
12586
Bulk power supply (BPS) redundancy has been lost on one or more row(s) of power
supplies in the complex. The further loss of a single BPS or an AC grid will most
likely result in the shutdown of partitions. Probable Cause: An AC source has been
lost. Recommended Action: Verify that the chassis is connected to working power
grid(s). WBEM EventID: 7253. WBEM ProviderName: FPL_IndicationProvider.
Error
12589
AC redundancy has been lost on one or more power supplies in the complex. The
further loss of a single Bulk Power Supply (BPS) or the other AC grid will most likely
result in the shutdown of partitions. Probable Cause: A change has occurred in the
number of properly operating bulk power supplies installed in the system.
Recommended Action: Replace missing or failed bulk power supplies. WBEM
EventID: 7255. WBEM ProviderName: FPL_IndicationProvider.
Error
12591
The fans that cool a region of the system are not redundant. If an additional fan fails
or is removed from this cooling domain, the partitions on this system will be shut
down to prevent damage. Probable Cause: One or more fans in the cooling domain
have been removed or are not functioning properly. Recommended Action: Removed
failed fan (if any) and insert working fan. WBEM EventID: 7256. WBEM
ProviderName: FPL_IndicationProvider.
Error
12593
An insufficient number of fans are working in a cooling domain to permit system
operation. Running partitions will be shut down immediately to prevent damage
due to excessive heat. Probable Cause: More than one fan in a cooling domain have
been removed or are not functioning properly. Recommended Action: Remove failed
fan(s), if any, and insert working fans. WBEM EventID: 7258. WBEM ProviderName:
FPL_IndicationProvider.
Error
12595
90
WBEM Provider Event Tables