HP Integrity rx2800 HP Insight Management WBEM Provider Events Reference Guide - Page 8
EventID: 114. WBEM ProviderName: SEL02_IndicationProvider.
View all HP Integrity rx2800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
5 Error A temperature inside the server has gone far outside the factory specified range. Probable Cause: The temperature inside the server has gone far outside the factory specified range for normal operation. To avoid permanent damage to your server hardware, go and turn off the server immediately. This event may indicate one of the following conditions: a failed fan blocked air vents or poor ventilation around the server open server chassis cover, or missing drive slot covers high temperature in the room where the server resides an unusually hot hardware component located near one of the server's temperature sensors. Recommended Action: Shutdown the system immediately. Find cause of temperature anomaly and fix it. WBEM EventID: 104. WBEM ProviderName: SEL02_IndicationProvider. 5 Error A temperature inside the server has gone far outside the factory specified range. Probable Cause: The temperature inside the server has gone far outside the factory specified range for normal operation. To avoid permanent damage to your server hardware, go and turn off the server immediately. This event may indicate one of the following conditions: a failed fan blocked air vents or poor ventilation around the server open server chassis cover, or missing drive slot covers high temperature in the room where the server resides an unusually hot hardware component located near one of the server's temperature sensors. Recommended Action: Shutdown the system immediately. Find cause of temperature anomaly and fix it. WBEM EventID: 104. WBEM ProviderName: SEL02_IndicationProvider. 6 Error Temperature sensor crossed upper non-recoverable threshold. Probable Cause: The temperature inside the server has gone far outside the factory specified range for normal operation. To avoid permanent damage to your server hardware, go and turn off the server immediately. This event may indicate one of the following conditions: a failed fan blocked air vents or poor ventilation around the server open server chassis cover, or missing drive slot covers high temperature in the room where the server resides an unusually hot hardware component located near one of the server's temperature sensors. Recommended Action: Shutdown the system immediately. Find cause of temperature anomaly and fix it. WBEM EventID: 105. WBEM ProviderName: SEL02_IndicationProvider. 6 Error Temperature sensor crossed upper non-recoverable threshold. Probable Cause: The temperature inside the server has gone far outside the factory specified range for normal operation. To avoid permanent damage to your server hardware, go and turn off the server immediately. This event may indicate one of the following conditions: a failed fan blocked air vents or poor ventilation around the server open server chassis cover, or missing drive slot covers high temperature in the room where the server resides an unusually hot hardware component located near one of the server's temperature sensors. Recommended Action: Shutdown the system immediately. Find cause of temperature anomaly and fix it. WBEM EventID: 105. WBEM ProviderName: SEL02_IndicationProvider. 8 Error A measured voltage in the server has gone far outside the factory specified lower voltage range. Probable Cause: The voltage in the server has gone outside the factory set range. A bad component, blown fuse, poorly seated module, loose cable, or debris could be responsible for this failure. Recommended Action: Check all boards, power supplies, and modules that either supply or use this voltage rail. WBEM EventID: 113. WBEM ProviderName: SEL02_IndicationProvider. 8 Error A measured voltage in the server has gone far outside the factory specified lower voltage range. Probable Cause: The voltage in the server has gone outside the factory set range. A bad component, blown fuse, poorly seated module, loose cable, or debris could be responsible for this failure. Recommended Action: Check all boards, power supplies, and modules that either supply or use this voltage rail. WBEM EventID: 113. WBEM ProviderName: SEL02_IndicationProvider. 9 Error Voltage sensor crossed lower non-recoverable threshold. Probable Cause: The voltage in the server has gone far outside the factory set range and could damage system components. A bad component, blown fuse, poorly seated module, loose cable, or debris could be responsible for this failure. Recommended Action: Check all boards, power supplies, and modules that either supply or use this voltage rail. WBEM EventID: 114. WBEM ProviderName: SEL02_IndicationProvider. 8 WBEM Provider Event Tables