HP Integrity rx2800 HP Insight Management WBEM Provider Events Reference Guide - Page 77

Failure writing IO backplane LPM. Probable Cause: IO Backplane LPM is

Get HP Integrity rx2800 - i2 PDF manuals and user guides View all HP Integrity rx2800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

11488 Error 11489 Error 11495 Warning 11496 Warning 11515 Warning 11521 Warning 11529 Warning 11530 Warning 11531 Warning 11537 Warning Failure writing the Onboard System Programmers (OSP) EEPROM. Probable Cause: device is not accessible over i2c. Recommended Action: check backplane power. WBEM EventID: 4924. WBEM ProviderName: FPL_IndicationProvider. SBS fault on startup. Probable Cause: SBS block for one of the MOAB's has reported an error on startup. Recommended Action: check backplane power. The physical location of the MOAB reporting the error is provided by data field. 0xFFFFXXFFFFFFFFFF where XX is: XX = 0x00 - Moab 0x00 XX = 0x01 - Moab 0x01 XX = 0x02 - Moab 0x02 XX = 0x10 - Moab 0x40 XX = 0x11 - Moab 0x41 XX = 0x12 Moab 0x42. WBEM EventID: 4925. WBEM ProviderName: FPL_IndicationProvider. Failure reading IO backplane LPM. Probable Cause: IO backplane LPM is not accessible over i2c. Recommended Action: Check power status of IO backplane. WBEM EventID: 4926. WBEM ProviderName: FPL_IndicationProvider. Failure writing IO backplane LPM. Probable Cause: IO Backplane LPM is not accessible over i2c. Recommended Action: Check power status of IO backplane. WBEM EventID: 4927. WBEM ProviderName: FPL_IndicationProvider. The system software violated one of the 'well-behavedness' rules of soft partitions and tried to call a firmware procedure within the firmware instance of a sibling. This is an access violation and firmware rejects the call. Probable Cause: System Software Defect - using the wrong entry address for the owner of the CPU. Recommended Action: Update the system software. WBEM EventID: 4928. WBEM ProviderName: FPL_IndicationProvider. AlbInitPrep was unable to read the ALREC_CONFIG CSR to determine whether the link is up or not. Data field: unused. Probable Cause: An error occurred while routing the fabric. Recommended Action: Collect IPMI event logs, and contact your HP support representative to inspect the fabric and system firmware. WBEM EventID: 4929. WBEM ProviderName: FPL_IndicationProvider. The fPar whose ID is identified in the event detail is disabled from booting because it has no bootable, healthy CPU. It may not own any CPU or the CPUs it owns are Unhealthy (or deconfigured). Probable Cause: The fPar whose ID is identified in the event detail is disabled from booting because it has no bootable, healthy CPU. It may not own any CPU or the CPUs it owns are Unhealthy (or deconfigured). Recommended Action: Use the soft partitioning configuration tool released with the OS product to reconfigure the fPar and reboot the partition. A cold reset of the hard partition may be required. WBEM EventID: 4930. WBEM ProviderName: FPL_IndicationProvider. Non-critical event announces that an fPar is enabled to boot but has inadequate memory resources to instantiate the firmware for the fPar. The configuration is modified to disable but not delete this fPar. Probable Cause: The user has configured an fPar to be booted with inadequate memory resources to instantiate the firmware image for this fPar. The fPar is software deconfigured (disabled) from booting. Recommended Action: Reconfigure the fPar, giving it at least instance-size (an fPars EFI variable) amount of physically contiguous RAM. Then re-enable and reset the fPar. WBEM EventID: 4931. WBEM ProviderName: FPL_IndicationProvider. The fPar has been enabled to boot, and contains at least one CPU and adequate memory but has not been given any IO resources. It must be reconfigured and reset before it may boot an operating system. Probable Cause: The fPar has been enabled to boot, and contains at least one CPU and adequate memory but has not been given any IO resources. The soft partition (fPar) may therefore only boot as far as the EFI shell. It must be reconfigured and reset before it may boot an operating system. Recommended Action: Reconfigure the soft partition using an Operating-system-specific utility then reset the soft partition. WBEM EventID: 4932. WBEM ProviderName: FPL_IndicationProvider. All processors are scheduled for deconfiguration. Probable Cause: All CPUs were scheduled to be deconfigured through a combination of user deconfigures and/or failures. Recommended Action: No action is required. WBEM EventID: 5270. WBEM ProviderName: FPL_IndicationProvider. Platform Events 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
Failure writing the Onboard System Programmers (OSP) EEPROM. Probable Cause:
device is not accessible over i2c. Recommended Action: check backplane power.
WBEM EventID: 4924. WBEM ProviderName: FPL_IndicationProvider.
Error
11488
SBS fault on startup. Probable Cause: SBS block for one of the MOAB's has reported
an error on startup. Recommended Action: check backplane power. The physical
location of the MOAB reporting the error is provided by data field.
0xFFFFXXFFFFFFFFFF where XX is: XX = 0x00 - Moab 0x00 XX = 0x01 - Moab 0x01
XX = 0x02 - Moab 0x02 XX = 0x10 - Moab 0x40 XX = 0x11 - Moab 0x41 XX = 0x12 -
Moab 0x42. WBEM EventID: 4925. WBEM ProviderName: FPL_IndicationProvider.
Error
11489
Failure reading IO backplane LPM. Probable Cause: IO backplane LPM is not
accessible over i2c. Recommended Action: Check power status of IO backplane.
WBEM EventID: 4926. WBEM ProviderName: FPL_IndicationProvider.
Warning
11495
Failure writing IO backplane LPM. Probable Cause: IO Backplane LPM is not
accessible over i2c. Recommended Action: Check power status of IO backplane.
WBEM EventID: 4927. WBEM ProviderName: FPL_IndicationProvider.
Warning
11496
The system software violated one of the 'well-behavedness' rules of soft partitions
and tried to call a firmware procedure within the firmware instance of a sibling. This
is an access violation and firmware rejects the call. Probable Cause: System Software
Defect - using the wrong entry address for the owner of the CPU. Recommended
Action: Update the system software. WBEM EventID: 4928. WBEM ProviderName:
FPL_IndicationProvider.
Warning
11515
AlbInitPrep was unable to read the ALREC_CONFIG CSR to determine whether the
link is up or not. Data field: unused. Probable Cause: An error occurred while routing
the fabric. Recommended Action: Collect IPMI event logs, and contact your HP
support representative to inspect the fabric and system firmware. WBEM EventID:
4929. WBEM ProviderName: FPL_IndicationProvider.
Warning
11521
The fPar whose ID is identified in the event detail is disabled from booting because
it has no bootable, healthy CPU. It may not own any CPU or the CPUs it owns are
Unhealthy (or deconfigured). Probable Cause: The fPar whose ID is identified in the
event detail is disabled from booting because it has no bootable, healthy CPU. It may
not own any CPU or the CPUs it owns are Unhealthy (or deconfigured).
Recommended Action: Use the soft partitioning configuration tool released with the
OS product to reconfigure the fPar and reboot the partition. A cold reset of the hard
partition may be required. WBEM EventID: 4930. WBEM ProviderName:
FPL_IndicationProvider.
Warning
11529
Non-critical event announces that an fPar is enabled to boot but has inadequate
memory resources to instantiate the firmware for the fPar. The configuration is
modified to disable but not delete this fPar. Probable Cause: The user has configured
an fPar to be booted with inadequate memory resources to instantiate the firmware
image for this fPar. The fPar is software deconfigured (disabled) from booting.
Recommended Action: Reconfigure the fPar, giving it at least instance-size (an fPars
EFI variable) amount of physically contiguous RAM. Then re-enable and reset the
fPar. WBEM EventID: 4931. WBEM ProviderName: FPL_IndicationProvider.
Warning
11530
The fPar has been enabled to boot, and contains at least one CPU and adequate
memory but has not been given any IO resources. It must be reconfigured and reset
before it may boot an operating system. Probable Cause: The fPar has been enabled
to boot, and contains at least one CPU and adequate memory but has not been given
any IO resources. The soft partition (fPar) may therefore only boot as far as the EFI
shell. It must be reconfigured and reset before it may boot an operating system.
Recommended Action: Reconfigure the soft partition using an
Operating-system-specific utility then reset the soft partition. WBEM EventID: 4932.
WBEM ProviderName: FPL_IndicationProvider.
Warning
11531
All processors are scheduled for deconfiguration. Probable Cause: All CPUs were
scheduled to be deconfigured through a combination of user deconfigures and/or
failures. Recommended Action: No action is required. WBEM EventID: 5270. WBEM
ProviderName: FPL_IndicationProvider.
Warning
11537
Platform Events
77