HP LH4r HP Netserver LXr 8500 Installation Guide - Page 110

HP NetServer LXr 8500 Rack Assembly and, Cabling Reference Guide

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

Chapter 8 Rack Mounting the HP NetServer The threaded inserts are located near the power inlet receptacle. Rear of NetServer Left Rear Rack Column Cable Management Arm Figure 8-12. Attaching the Cable Management Arm 4. Attach the flange to the HP NetServer with the two 6-32 pan head Torx® T-15 screws, included with the Arm. See Figure 8-12. 5. Attach the other flange of the cable arm to the rear column of the rack with the two M-5 pan head T-25 Torx® screws, included with the Arm. See Figure 8-12. 6. Extend the HP NetServer out of the rack to ensure the Cable Management Arm moves along with the chassis without binding. 7. Plug the HP NetServer's power cable and any available data cables into the back of the HP NetServer. NOTE Refer to the HP NetServer LXr 8500 Rack Assembly and Cabling Reference Guide for information about cable dressing and routing. 8. Dress the cables in the Cable Management Arm and then slide the HP NetServer into the rack to verify the cables don't bind in the tray. 102

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Chapter 8
Rack Mounting the HP NetServer
102
The threaded inserts are located near the power inlet receptacle.
Left Rear
Rack Column
Rear of NetServer
Cable Management Arm
Figure 8-12. Attaching the Cable Management Arm
4.
Attach the flange to the HP NetServer with the two 6-32 pan head Torx
®
T-15 screws, included with the Arm. See Figure 8-12.
5.
Attach the other flange of the cable arm to the rear column of the rack with
the two M-5 pan head T-25 Torx
®
screws, included with the Arm.
See Figure 8-12.
6.
Extend the HP NetServer out of the rack to ensure the Cable Management
Arm moves along with the chassis without binding.
7.
Plug the HP NetServer’s power cable and any available data cables into the
back of the HP NetServer.
NOTE
Refer to the
HP NetServer LXr 8500 Rack Assembly and
Cabling Reference Guide
for information about cable dressing
and routing.
8.
Dress the cables in the Cable Management Arm and then slide the HP
NetServer into the rack to verify the cables don’t bind in the tray.