HP LH4r HP Netserver LXr 8500 Installation Guide - Page 35

Opening and Closing the, HP NetServer

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

3 Opening and Closing the HP NetServer Removing and Replacing the Front Bezel The front bezel is attached to the front of the HP NetServer using a hinge and latch. The bezel is mounted onto the hinge with three clips. You can swing the bezel open on its hinge, or remove the bezel entirely. NOTE HP NetServers installed in non-HP racks use a different front bezel for mounting. For more information, refer to the separate rack-mounting guide for third-party racks. It is packed in the accessories tray in the HP NetServer's shipping box. 1. To swing open the bezel, grasp it by the handle on its right edge and pull it open to the left. This exposes the mass storage devices and memory board bays (covered). 2. To remove the front bezel, pull it straight forward off the chassis. 3. To replace the bezel, press it back onto the chassis, allowing it to snap into place. See Figure 3-1. Figure 3-1. Removing and Replacing the Front Bezel 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
27
3
Opening and Closing the
HP NetServer
Removing and Replacing the Front Bezel
The front bezel is attached to the front of the HP NetServer using a hinge and
latch. The bezel is mounted onto the hinge with three clips. You can swing the
bezel open on its hinge, or remove the bezel entirely.
NOTE
HP NetServers installed in non-HP racks use a different front
bezel for mounting. For more information, refer to the separate
rack-mounting guide for third-party racks.
It is packed in the
accessories tray in the HP NetServer’s shipping box.
1.
To swing open the bezel, grasp it by the handle on its right edge and pull it
open to the left.
This exposes the mass storage devices and memory board bays (covered).
2.
To remove the front bezel, pull it straight forward off the chassis.
3.
To replace the bezel, press it back onto the chassis, allowing it to snap into
place.
See Figure 3-1.
Figure 3-1. Removing and Replacing the Front Bezel