HP LH4r HP Netserver LXr 8500 Installation Guide - Page 54

Filler, Panel, Mounting Rails 2 &amp, Screws 4, Cover, Screws 2, Post center

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Chapter 4 Screws (2) Cover Installing Mass Storage Devices Post (center) Mounting Rails (2) & Screws (4) Filler Panel Figure 4-5. Removing the Peripheral Bay Cover 15. Connect the two mounting rails from the filler panel to the tape drive. 16. Insert the tape drive into the peripheral bay, securing it in place, and then connect the cables (data and power) to the tape drive. 17. To install the peripheral bay and return power to the HP NetServer, reverse Steps 1 through 10, and add Steps 18 and 19. CAUTION To prevent damage to the metal EMI clips and copper grounding gasket, use caution when inserting the peripheral bay and the memory bay cover. 18. Insert the peripheral bay slowly to ensure you engage the center post of the peripheral bay with the memory board guide bracket. To align the peripheral bay with its connector at the rear of the bay, the center post and memory board guide bracket must mate together as it moves into the bay. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Chapter 4
Installing Mass Storage Devices
46
Filler
Panel
Mounting Rails (2) &
Screws (4)
Cover
Screws (2)
Post (center)
Figure 4-5. Removing the Peripheral Bay Cover
15.
Connect the two mounting rails from the filler panel to the tape drive.
16.
Insert the tape drive into the peripheral bay, securing it in place, and then
connect the cables (data and power) to the tape drive.
17.
To install the peripheral bay and return power to the HP NetServer, reverse
Steps 1 through 10, and add Steps 18 and 19.
CAUTION
To prevent damage to the metal EMI clips and copper
grounding gasket, use caution when inserting the peripheral
bay and the memory bay cover.
18.
Insert the peripheral bay slowly to ensure you engage the center post of the
peripheral bay with the memory board guide bracket.
To align the peripheral bay with its connector at the rear of the bay, the
center post and memory board guide bracket must mate together as it
moves into the bay.