HP LH4r HP Netserver LXr 8500 Installation Guide - Page 134

CSCSI Configuration Utility

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 134 highlights

Chapter 10 Configuring the HP NetServer 2. Once in the utility, press the F9 key. A dialog box appears with this message: Load default configuration now? 3. Choose Yes from the dialog box. 4. Use the right-arrow or left-arrow key to go to the Advanced menu. 5. Once there, use the down-arrow key to move to the Reset Configuration Data field. 6. Then, choose Yes. 7. Use the right-arrow or left-arrow key to go to the HP NetServer menu. 8. Once there, use the down-arrow key to go to the Server Processor Retest field. 9. Once there, choose Yes. 10. Press F10 to save the configuration changes and exit. The HP NetServer reboots. SCSI Configuration Utility The HP NetServer uses the Symbios Configuration Utility as its SCSI Configuration Utility. If you need to verify or modify SCSI host adapter settings, low-level format SCSI disks, or verify SCSI disk media, run the Symbios Configuration Utility as follows: 1. Turn on or reboot your system. 2. During system start-up or reset, when the following message appears, press the [CTRL] and [C] keys at the same time. Press [Ctrl] [C] to start Symbios Configuration Utility 3. Use the arrow keys to move the cursor, press [Enter] to select an option, and press [Esc] to exit. 4. To change adapter settings: ◊ Select an adapter from the list in the main menu. ◊ Select Adapter Setup. 126

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Chapter 10
Configuring the HP NetServer
126
2.
Once in the utility, press the
F9
key.
A dialog box appears with this message:
Load default configuration now?
3. Choose
Yes
from the dialog box.
4.
Use the right-arrow or left-arrow key to go to the
Advanced
menu.
5.
Once there, use the down-arrow key to move to the
Reset Configuration Data
field.
6.
Then, choose
Yes
.
7.
Use the right-arrow or left-arrow key to go to the HP NetServer menu.
8.
Once there, use the down-arrow key to go to the
Server Processor
Retest
field.
9.
Once there, choose
Yes
.
10. Press
F10
to save the configuration changes and exit.
The HP NetServer reboots.
SCSI Configuration Utility
The HP NetServer uses the Symbios Configuration Utility as its SCSI
Configuration Utility. If you need to verify or modify SCSI host adapter settings,
low-level format SCSI disks, or verify SCSI disk media, run the Symbios
Configuration Utility as follows:
1.
Turn on or reboot your system.
2.
During system start-up or reset, when the following message appears, press
the [
CTRL
] and [
C
] keys at the same time.
Press [Ctrl] [C] to start Symbios
Configuration Utility
3.
Use the arrow keys to move the cursor, press [
Enter
] to select an option,
and press [
Esc
] to exit.
4.
To change adapter settings:
◊
Select an adapter from the list in the main menu.
◊
Select
Adapter Setup
.