HP LH4r HP Netserver LXr 8500 Installation Guide - Page 79

If the Cable Management Arm is not used, use caution when

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

Chapter 6 A. Push the PCI hold-down latch in from the rear. Installing Additional Boards B. The latch should click into place. C. Close the latch on the PCI board guide. Figure 6-7. Closing the PCI Hold-Down Latch NOTE If the PCI hold-down latch does not fully close (click), the slot will not be powered on when the HP NetServer reboots. 16. If the accessory board(s) installation is complete, install the PCI access panel. Refer to Chapter 3, "Opening and Closing the HP NetServer." CAUTION If the Cable Management Arm is not used, use caution when sliding the chassis into the rack to prevent damage to cables. 17. Slide the chassis back into the rack. Refer to Chapter 3, "Opening and Closing the HP NetServer." 18. Re-install the bezel onto the front of the HP NetServer. 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Chapter 6
Installing Additional Boards
71
A. Push the
PCI hold-down
latch in from
the rear.
B. The latch
should click
into place.
C. Close the
latch on the
PCI board guide.
Figure 6-7. Closing the PCI Hold-Down Latch
NOTE
If the PCI hold-down latch does not fully close (click), the slot
will not be powered on when the HP NetServer reboots.
16.
If the accessory board(s) installation is complete, install the PCI access
panel.
Refer to Chapter 3, "Opening and Closing the HP NetServer."
CAUTION
If the Cable Management Arm is not used, use caution when
sliding the chassis into the rack to prevent damage to cables.
17.
Slide the chassis back into the rack.
Refer to Chapter 3, "Opening and Closing the HP NetServer."
18.
Re-install the bezel onto the front of the HP NetServer.