HP LH4r HP Netserver LXr 8500 Installation Guide - Page 133

Clearing CMOS

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 133 highlights

Chapter 10 Configuring the HP NetServer 1. ATAPI CD-ROM Drive 2. Removable Devices 3. Hard Drive The list provides the current boot order of the HP NetServer's internal mass storage devices. In this list, Removable Devices refers to the HP NetServer's flexible disk drive. 4. To change the order, use the up- and down-arrow keys to select one of the devices. 5. Use the plus (+) or minus (-) keys to move the device up or down the list. 6. Press Esc to exit the Boot Device Priority menu. 7. To change the hard driver boot order, scroll to Hard Drive and press Enter. Refer to Hard Drive Multi-Boot Support in Information Assistant on the HP NetServer Online Documentation CD-ROM under Configure for more information. 8. Use the plus (+) key to move the desired hard drive (or DAC) to the top of the list. NOTE If Multi-boot is Enabled (default setting) and you want the HP NetServer to boot from a specific hard drive, you must select the specific hard drive from the list to ensure the HP NetServer will boot from the desired hard drive. 9. Press Esc to exit the Hard Drive menu. 10. Press Esc again to exit the Boot menu. 11. Use the right- or left-arrow keys to select the Exit menu. 12. Choose Exit Saving Changes from the list of exit options, then press Enter. A dialog appears asking you to confirm your decision. 13. Choose Yes and press Enter. The HP NetServer then reboots. Clearing CMOS To clear CMOS from within the setup utility, refer to the following procedure. 1. Start the setup utility. 125

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Chapter 10
Configuring the HP NetServer
125
1. ATAPI CD-ROM Drive
2. Removable Devices
3. Hard Drive
The list provides the current boot order of the HP NetServer’s internal
mass storage devices. In this list,
Removable Devices
refers to the HP
NetServer's flexible disk drive.
4.
To change the order, use the up- and down-arrow keys to select one of the
devices.
5.
Use the plus (
+
) or minus (
-
) keys to move the device up or down the list.
6. Press
Esc
to exit the Boot Device Priority menu.
7.
To change the hard driver boot order, scroll to Hard Drive and press
Enter
.
Refer to
Hard Drive Multi-Boot Support
in Information Assistant on the
HP NetServer Online Documentation CD-ROM
under Configure for more
information.
8.
Use the plus (
+
) key to move the desired hard drive (or DAC) to the top of
the list.
NOTE
If Multi-boot is
Enabled
(default setting) and you want the HP
NetServer to boot from a specific hard drive, you must select
the specific hard drive from the list to ensure the HP NetServer
will boot from the desired hard drive.
9. Press
Esc
to exit the Hard Drive menu.
10. Press
Esc
again to exit the Boot menu.
11.
Use the right- or left-arrow keys to select the
Exit
menu.
12. Choose
Exit Saving Changes
from the list of exit options, then press
Enter
.
A dialog appears asking you to confirm your decision.
13. Choose
Yes
and press
Enter
.
The HP NetServer then reboots.
Clearing CMOS
To clear CMOS from within the setup utility, refer to the following procedure.
1.
Start the setup utility.