HP LH4r HP Netserver LXr 8500 Installation Guide - Page 113
and bezel latch.
 |
View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 113 highlights
Chapter 8 Rack Mounting the HP NetServer Figure 8-15. Attaching the Bezel Latch 6. At the front of the rack, insert the screws through the flanges into the rack nuts and secure the HP NetServer to the front rack columns with a Torx® T-25 driver. Each of the HP NetServer's two front flanges has two slots, which should line up with the rack nuts previously mounted on the rack columns. 7. Hold the bezel in front of the HP NetServer and line it up with the hinge and bezel latch. 8. Press it firmly into place, especially at the top-left and bottom-left corners. You should hear several clicks as the bezel snaps into place on the hinge and latch. See Figure 8-16. 105
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108 -
109 -
110 -
111 -
112 -
113 -
114 -
115 -
116 -
117 -
118 -
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
 |
 |
Chapter 8
Rack Mounting the HP NetServer
105
Figure 8-15. Attaching the Bezel Latch
6.
At the front of the rack, insert the screws through the flanges into the rack
nuts and secure the HP NetServer to the front rack columns with a Torx
®
T-25 driver.
Each of the HP NetServer’s two front flanges has two slots, which should
line up with the rack nuts previously mounted on the rack columns.
7.
Hold the bezel in front of the HP NetServer and line it up with the hinge
and bezel latch.
8.
Press it firmly into place, especially at the top-left and bottom-left corners.
You should hear several clicks as the bezel snaps into place on the hinge
and latch. See Figure 8-16.