HP LH4r HP Netserver LXr 8500 Installation Guide - Page 65

Guide, Rails, Memory, Board, Front of HP NetServer, Connector

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Chapter 5 Installing Additional Memory 21. Once all DIMMs have been installed on the memory board or boards, you are ready to re-install each one into the HP NetServer. NOTE If the either memory slot is empty, the BIOS detects and ignores it during the boot process. 22. To install the memory board into either memory bay slot, align the memory board with its respective guide rails. See Figure 5-7. Ensure the component-side (DIMMs) of the memory board faces down. Guide Rails Connector Memory Board Front of HP NetServer Figure 5-7. Replacing the Memory Board 23. Slide the board into the guide rails of the memory bay. See Figure 5-7. Ensure the LCD display does not interfere with the right memory board. 24. Push the board in until it meets the slot's connector at the rear of the bay. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
Chapter 5
Installing Additional Memory
57
21.
Once all DIMMs have been installed on the memory board or boards, you
are ready to re-install each one into the HP NetServer.
NOTE
If the either memory slot is empty, the BIOS detects and
ignores it during the boot process.
22.
To install the memory board into either memory bay slot, align the
memory board with its respective guide rails. See Figure 5-7.
Ensure the component-side (DIMMs) of the memory board faces down.
Guide
Rails
Memory
Board
Front of HP NetServer
Connector
Figure 5-7. Replacing the Memory Board
23.
Slide the board into the guide rails of the memory bay. See Figure 5-7.
Ensure the LCD display does not interfere with the right memory board.
24.
Push the board in until it meets the slot’s connector at the rear of the bay.